The engineering workbench / general tolerances
GB/T 1804-m Tolerance: General Tolerances Explained
Look up symmetrical linear size deviations for classes f, m, c and v. This calculator uses the GB/T 1804-2000 / ISO 2768-1:1989 size intervals, excluding broken edges.
Linear dimensions only: 0.5–4000 mm where a value is tabulated. Chamfer heights, broken-edge radii and angular tolerances use separate tables and are outside this calculator.
02 / Read the limits
Results
Size deviations use ±. Geometrical results are tolerance-zone widths.
| Characteristic | Result · mm | Interpretation |
|---|
A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.
03 / How to use
How to use this calculator
- Use this GB/T 1804 calculator for linear dimensions only. It uses the GB/T 1804-2000 / ISO 2768-1:1989 linear tables, not ISO 2768:2026. Angular tolerances, chamfer heights and broken-edge radii are outside this calculator.
- Choose the class shown in the drawing title block: f, m, c or v. For a note such as GB/T 1804-m, choose m.
- Enter the nominal linear size from 0.5 mm up to and including 4000 mm. The calculator uses the size band that contains your entry; some class and size combinations have no tabulated value.
- Read the permissible deviation in the calculator result. Apply it to the dimension as the drawing and the standard require, and leave any individually indicated tolerance unchanged.
The result is the standard's tabulated permissible deviation for the selected class and size band; this page intentionally does not reproduce the numeric tables.
Table lookup, with explicit boundaries
Lower limit = nominal size − t; upper limit = nominal size + t.
Total size tolerance width = 2 × t.
The first interval includes its lower tabulated size. Each following interval excludes its lower endpoint and includes its upper endpoint. The calculator rejects inputs outside the stated range and does not round inputs across a boundary.
04 / Engineering context
GB/T 1804-m Tolerance: General Tolerances for Linear and Angular Dimensions
GB/T 1804-m tolerance is the medium-class general tolerance defined in GB/T 1804-2000, the Chinese national standard for linear and angular dimensions that carry no individual tolerance indication. Instead of writing a separate limit on every dimension, a drawing can invoke one general class in or near the title block. That class then supplies the permissible deviation for all applicable untoleranced dimensions. GB/T 1804 defines four classes — f, m, c and v — running from fine to very coarse, with m as the medium class.
The standard is used for dimensions produced mainly by metal cutting and for general press-formed sheet-metal dimensions. It covers linear and angular dimensions without individual tolerance indications. It does not replace functional tolerances, fits or geometrical controls, and it does not override a tolerance written directly on a feature. An indicated tolerance always takes precedence; general tolerances fill the gaps on a drawing.
GB/T 1804-2000 is an equivalent adoption (eqv) of ISO 2768-1:1989, so its four class letters and general approach correspond to the ISO standard. The ISO catalogue now lists ISO 2768-1:1989 as withdrawn and revised by ISO 2768:2026, while GB/T 1804-2000 remains the Chinese edition discussed here; confirm the edition named in your contract. For existing drawings, the correspondence is still useful: a note such as GB/T 1804-m and ISO 2768-m both point to medium-class general tolerances for untoleranced linear and angular dimensions.
05 / GB · ISO · DIN
Compare the specified editions
| Standard | Scope / classes | Relationship used here |
|---|---|---|
| GB/T 1804-2000 | Linear and angular general tolerances; f, m, c, v | Chinese adoption of ISO 2768-1:1989; the official record describes the adoption as equivalent. This tool implements only the linear table. |
| ISO 2768-1:1989 | Linear and angular dimensions; f, m, c, v | The edition compared here. Geometrical class K belongs to part 2. |
| DIN ISO 2768-1:1991-06 | German publication of ISO 2768-1:1989 | DIN describes this edition as identical to ISO 2768-1:1989. Confirm the edition on the drawing. |
This page targets the named historical editions. ISO lists ISO 2768-1:1989 as withdrawn with ISO 2768:2026 available, and ISO 2768-2:1989 as withdrawn with ISO 22081:2021 available. These calculators do not implement the replacement standards. Use the edition specified on the drawing.
06 / Questions
Frequently asked questions
What does the "m" in GB/T 1804-m mean?
The m is the medium tolerance class in GB/T 1804. It sits between f (fine) and c (coarse) and is one of four classes: f, m, c and v.
Is GB/T 1804 the same as ISO 2768-1?
GB/T 1804-2000 is an equivalent adoption of ISO 2768-1:1989, not a separately invented system. The class letters and general-tolerance concept align, but the Chinese standard remains its own document; use the edition and standard named in the drawing or contract.
Does GB/T 1804 cover angular dimensions?
Yes. The standard covers both linear and angular dimensions without individual tolerance indications. For angles, the tolerance depends on the length of the shorter side. This calculator implements only the linear table; it does not provide angular, chamfer-height or broken-edge radius tables.
Do general tolerances apply when a dimension already has a tolerance?
No. A tolerance written directly beside a dimension takes precedence over the general tolerance. General tolerances apply only where the drawing does not give an individual tolerance for that dimension.
Does GB/T 1804 control straightness, flatness or position?
No. GB/T 1804 deals with linear and angular dimensions. General geometrical tolerances are covered separately by GB/T 1184, which corresponds to ISO 2768-2. Functional geometrical requirements still need explicit symbols and datums.
Can I use GB/T 1804 for sheet metal?
The standard's scope includes general press-formed sheet-metal dimensions as well as metal-cutting dimensions. That does not guarantee every sheet-metal feature can hold the selected class; confirm process capability and any customer-specific drawing requirements.
How do I choose between f, m, c and v?
Choose the loosest class that still satisfies function, fit and inspection needs. A tighter class can raise cost and may not match the process. The class should be a deliberate drawing decision, not an arbitrary default.