EngineeringFitsEnglish tool

The engineering workbench / general tolerances

ISO 2768-mK Tolerance Chart: Classes and Meaning

Read the class m linear tolerance and class K general geometrical tolerances for a drawing specifying ISO 2768-1:1989 and ISO 2768-2:1989. Set each feature’s controlling length separately.

Linear size: 0.5–4000 mm. Geometrical lengths: greater than 0 and up to 3000 mm. This is a selected lookup for legacy mK drawings, not a complete implementation of every general-tolerancing rule.

02 / Read the limits

Results

Size deviations use ±. Geometrical results are tolerance-zone widths.

CharacteristicResult · mmInterpretation

A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.

03 / How to use

How to use this calculator

  1. Use this ISO 2768-mK calculator only when the drawing specifies the legacy classes m and K. The classes are fixed on this page: m for linear sizes and K for the selected geometrical characteristics. Angular, chamfer-height and broken-edge radius tables are not implemented.
  2. Enter the nominal linear size from 0.5 mm up to and including 4000 mm. Enter each geometrical controlling length separately, greater than 0 and up to 3000 mm: the line length or surface's longer side (diameter for a circular surface) for straightness or flatness, the shorter side for perpendicularity, and the controlled feature length for symmetry. Circular run-out uses a class-only value and needs no length input.
  3. Read the permissible deviation or tolerance from the calculator result. Part 1 results are size deviations; Part 2 results are geometrical tolerance zones.
  4. Check the drawing for any individually indicated tolerance or feature control frame. An explicit callout takes precedence over the general tolerance for the dimension or geometrical characteristic it controls.

Table lookup, with explicit boundaries

Linear: read t from part 1, class m; size limits = nominal size ± t.
Geometry: read the class K tolerance-zone width using the relevant feature length; do not apply ± to it.
Circular run-out uses a class-only value.

The first interval includes its lower tabulated size. Each following interval excludes its lower endpoint and includes its upper endpoint. The calculator rejects inputs outside the stated range and does not round inputs across a boundary.

04 / Engineering context

ISO 2768-mK Tolerance Chart: How to Read the Two-Part Callout

An ISO 2768-mK tolerance chart is really two lookups in one drawing note. ISO 2768-1 defines general tolerances for linear and angular dimensions that have no individual tolerance indication, using classes f, m, c and v. ISO 2768-2 defines general geometrical tolerances for features without individual tolerance indications, using classes H, K and L. The lowercase m comes from Part 1; the uppercase K comes from Part 2. Together they tell the shop that untoleranced size dimensions follow medium-class general tolerances and untoleranced geometrical characteristics follow class K.

Part 1 applies to dimensions of workpieces produced by metal removal or formed from sheet metal. It simplifies drawings by replacing repeated tolerance notes with a single class. Part 2 mainly applies to features produced by removal of material. Its four explicit tables cover straightness and flatness, perpendicularity, symmetry and circular run-out; the standard also explains how some other characteristics, such as roundness and parallelism, relate to size or other general tolerances. It does not provide a dedicated default for every geometrical control, so position, profile and similar requirements need explicit specification where they are functionally important.

Both parts date from 1989 and remain common on legacy drawings. ISO 2768:2026, Edition 2, was published on 2026-11-09 at stage 60.60 and replaces the withdrawn ISO 2768-1:1989. Its title is "Geometrical product specifications (GPS) — Dimensional tolerancing — Tolerance limits for general specification of linear and angular sizes". ISO 2768-2:1989 was withdrawn on 2021-02-04 and revised by ISO 22081:2021. That does not make an existing mK drawing unreadable: the drawing and its contract still control the job, and new designs should confirm which current specification applies. The mK notation itself should be read as two coordinated classes, not as a single grade called "mK".

ISO 2768:2026 applies to features with nominal linear sizes from 0.5 mm up to and including 4000 mm and any nominal angular size. It excludes other dimensional specifications, including linear and angular distances; see ISO 14405-2. It can be used with ISO 22081 when the interactions are unambiguously described. This calculator still uses the ISO 2768-1:1989 / GB/T 1804-2000 linear tables and the ISO 2768-2:1989 / GB/T 1184-1996 geometrical tables described below; it does not implement ISO 2768:2026 or ISO 22081:2021.

05 / GB · ISO · DIN

Compare the specified editions

StandardScope / classesRelationship used here
GB/T 1804-2000 + GB/T 1184-1996Dimensional and geometrical requirements are separateClass m linear values use the same table here. K straightness/flatness reuses the existing GB/T 1184 /form/ table. Other GB mappings are not asserted by this tool.
ISO 2768-1:1989 + ISO 2768-2:1989m = dimensional class; K = geometrical classBoth class letters matter. Geometrical controlling lengths can differ from the nominal linear size.
DIN ISO 2768-1:1991-06 + DIN ISO 2768-2:1991-04German publications of the two ISO editionsA matching class code is not permission to substitute a different edition or general specification framework.

This page targets the named historical editions. ISO lists ISO 2768-1:1989 as withdrawn with ISO 2768:2026 available, and ISO 2768-2:1989 as withdrawn with ISO 22081:2021 available. These calculators do not implement the replacement standards. Use the edition specified on the drawing.

06 / Questions

Frequently asked questions

What does mK mean in a drawing title block?

ISO 2768-mK combines two general-tolerance classes. The m is the ISO 2768-1 medium class for linear and angular dimensions; the K is the ISO 2768-2 class for geometrical tolerances. It applies to features that do not carry individual tolerances, and explicit tolerances still override it.

Is mK a single tolerance grade?

No. m and K come from different parts of ISO 2768 and control different things. m controls untoleranced linear and angular dimensions; K controls untoleranced geometrical characteristics. The two letters are written together only for convenience in the title block.

Which geometrical characteristics does ISO 2768-2 cover?

Its four explicit tables cover straightness and flatness, perpendicularity, symmetry and circular run-out. The standard also discusses derived defaults for characteristics such as roundness and parallelism. It does not provide a dedicated general value for every characteristic, so position and profile need explicit control where they matter.

Does ISO 2768-mK cover both size and geometry?

Yes, when both parts are invoked. A note with only m addresses Part 1; a note with only K addresses Part 2. The combined mK note tells the reader to apply both sets of general tolerances.

Is ISO 2768-1 the same as ISO 2768-2?

No. ISO 2768-1:1989 covers linear and angular dimensions; ISO 2768-2:1989 covers geometrical tolerances. These legacy editions can be invoked together, as in mK. They have been withdrawn and replaced by ISO 2768:2026 and ISO 22081:2021, respectively.

Can I still use ISO 2768-mK on a new drawing?

ISO 2768-1:1989 and ISO 2768-2:1989 have been withdrawn and revised in the ISO system. Many contracts still call them out, so always follow the drawing and customer agreement. For new work, confirm whether ISO 2768:2026, ISO 22081:2021 or explicit GPS specifications are required.

Why does the calculator ask for a size or length?

The linear, straightness/flatness, perpendicularity and symmetry lookups use size or feature-length bands. Enter each feature's relevant length separately; circular run-out uses a class-only value. The calculator returns values for the fixed legacy m and K classes. This page does not reproduce the numeric tables; read the result shown by the calculator.

Does mK override a feature control frame?

No. A feature control frame or a tolerance written directly on a dimension is an individual requirement and takes precedence over the general tolerance for that dimension or geometrical characteristic. General tolerances can still apply to other characteristics without individual tolerances.