Room to move
The smallest hole is at least as large as the largest shaft. Minimum clearance may be zero.
TRY H7/g6THE ENGINEERING WORKBENCH
Hole and shaft limits, without the table hunting.
Find your fit and see exactly where it lands.
ONE BASIC SIZE.
TWO TOLERANCE ZONES.
A CLEAR ANSWER.
YOUR FIT
Hole ShaftVertical scale proportional to deviation
| Feature | Lower dev. | Upper dev. | Min. size | Max. size |
|---|
Loading calculator…
HOW TO USE
READ THE RESULT
The fit describes the possible gap between the hole and shaft at their size limits.
The smallest hole is at least as large as the largest shaft. Minimum clearance may be zero.
TRY H7/g6Either clearance or interference is possible, depending on the actual sizes of the two parts.
TRY H7/k6The smallest shaft is at least as large as the largest hole. Assembly conditions need separate assessment.
TRY H7/p6THE NOTATION
H7 specifies the hole; g6 specifies the shaft. The letter locates the tolerance zone relative to the basic size. The number is the IT grade, which sets the zone width.
A hole-basis fit uses an H hole with zero lower deviation. A shaft-basis fit uses an h shaft with zero upper deviation.
A WORKED EXAMPLE
See the hole and shaft limits at 20 mm and 50 mm, learn how to calculate the gap, and compare H7/g6 with H7/h6.
THE SYSTEM
ISO 286 is the international code system for tolerances on linear sizes. Part 1, ISO 286-1, defines the vocabulary and the rules: nominal size, upper and lower limit deviations, the standard tolerance grades designated IT, and the fundamental-deviation letters that position each tolerance zone. Part 2, ISO 286-2, turns those rules into tables of limit deviations for commonly used hole and shaft classes. Together they let a drawing say H7/g6 instead of carrying a pair of calculated limits for every mating feature. The standard is written around two kinds of feature of size: a cylinder and two parallel opposite surfaces. Its classes are nevertheless used on diameters, widths, slots and other linear features, which is why the same letters appear on shafts that are not round. The system controls the distance across the feature, not its roundness, straightness, position or surface texture. A feature can be within its size limits and still be out of round, so a fit that depends on form or surface quality needs those requirements separately.
The letter and the number do different jobs. The letter, capital for a hole and lowercase for a shaft, is the fundamental deviation and fixes the position of the tolerance zone relative to the nominal size. Examples include G, H, K and P for holes and g, h, k and p for shafts. The IT number fixes the width of that zone. H and h are the reference classes: an H hole has its lower limit at the nominal size, and an h shaft has its upper limit at the nominal size. In a hole-basis fit the hole is H and the shaft letter varies, as in H7/g6 or H7/p6. In a shaft-basis fit the shaft is h and the hole letter varies, as in G7/h6. Hole-basis is the more common workshop convention, but both belong to the same system.
Fits fall into three families. A clearance fit leaves the hole larger than the shaft, or allows the two limits to meet line-to-line; a transition fit can produce either clearance or interference; an interference fit leaves the shaft larger, or again allows line-to-line contact at the extreme. Those descriptions state the relationship of the two tolerance zones, not a promise about a particular assembly. The actual clearance or interference for a given nominal size comes from the tabulated limit deviations, and the designer still has to judge load, lubrication, temperature, material and assembly method.
KNOW YOUR BOUNDARIES
This calculator implements a selected metric subset: basic sizes 1–500 mm, grades IT5–IT13, and the D, E, F, G, H, JS, K, M, N, P, R and S zones and their shaft equivalents. Other classes are not offered. For N9–N13 holes, basic size must be greater than 1 mm.
Calculation references: ISO 286-1:2010 and ISO 286-2:2010. This is an independent implementation, not an ISO publication or certification.
Limits describe dimensional fits only. Surface texture, temperature, material, form, assembly force and functional suitability need separate engineering assessment.
Minimum signed clearance = minimum hole size − maximum shaft size. Maximum signed clearance = maximum hole size − minimum shaft size. Negative signed clearance means interference. For an interference fit, the displayed interference magnitudes are positive.
This version uses metric ISO classes only. Converting units does not turn an ISO fit into an ANSI/ASME B4.1 fit. An inch-fit calculator and cross-standard index are outside this version.
ISO tolerances use size intervals. An upper interval boundary belongs to that interval: 50 mm uses the above-30-to-50-mm IT range; a size just above 50 mm uses the next range. Fundamental deviations can use finer intervals.
QUESTIONS
ISO 286 sets out a code system for tolerances on linear sizes, including the fundamental deviations and standard tolerance grades used to define hole and shaft classes. It provides the basis for expressing fits such as H7/g6. It does not cover every geometrical or surface requirement of a part.
ISO 286-1 gives the basis: definitions, the IT grade system, the fundamental-deviation rules and the principles of hole-basis and shaft-basis fits. ISO 286-2 provides tables of limit deviations for commonly used hole and shaft classes. The first explains the system; the second supplies the tabulated values for a nominal size.
The part before the slash is the hole class and the part after it is the shaft class. H7 is an H hole with IT7 tolerance width; g6 is a g shaft with IT6 tolerance width. The pair is a hole-basis fit because the hole is H. Read the actual limits for both classes at the same nominal size before judging the fit.
In a hole-basis fit, every hole in the fit uses the H fundamental deviation and the shaft class is changed to produce the required clearance or interference. In a shaft-basis fit, the shaft uses h and the hole class is changed. Hole-basis is common because one hole class can serve several shaft classes, but shaft-basis is useful when the shaft is already fixed by a standard component.
A clearance fit always provides clearance, or line-to-line contact at its extreme limits. A transition fit may produce either clearance or interference, depending on the actual sizes of the two parts. An interference fit always produces interference, or line-to-line contact at its extreme, so assembly normally needs force or a temperature change.
No. The standard is written for cylinders and for two parallel opposite surfaces, so it also applies to widths and thicknesses. The words hole and shaft are used for the internal and external features of size, whether or not the feature is circular.
No. A class such as H7 or h6 controls the size of the feature. Roundness, cylindricity, straightness, orientation, position and surface texture need separate specifications when they matter to the function. A part can meet its size limits and still fail a form or finish requirement.
The page explains the system and the meaning of the classes. The numerical limit deviations depend on the nominal size and the selected class, so they are read from the calculator result or the tables rather than reproduced here. That avoids quoting a value that belongs to a different size band.