01 / THE NOTATION

What the fit is

This general-purpose pair suits shafts that rotate or slide with enough freedom for a lubricant film, thermal movement or easy assembly. It does not define the lubricant, surface finish or operating temperature.

H8 has its lower deviation at zero and the IT8 width; f7 sits below nominal with the IT7 width. The hole is therefore always larger than the shaft.

Clearance is positive when the hole is larger: c_min = EI - es, c_max = ES - ei. The minimum comes from the negative shaft upper deviation; the maximum combines both tolerance widths and the shaft offset.

It is running clearance, not a transition or interference fit, and not a close locational fit: the minimum clearance is deliberately positive.

02 / WHERE IT FITS

Typical uses

H8/f7 is used for sliding shafts, plain-bearing journals, guide rods, pump and small-machine shafts, conveyor rollers, lightly loaded spindles and similar running parts where easy assembly and a lubricant film matter more than minimal play.

It is less suitable where accurate centring is required, clearance must be small, or load and speed demand a designed bearing. Too much clearance causes impact and poor film formation; too little causes heating or seizure.

Bearing manufacturers publish specific fits; H8/f7 is a general pair, not a universal bearing specification.

03 / WORK IT THROUGH

Limit deviations and worked examples

The table gives limit deviations in micrometres. ES/EI are hole upper/lower deviations; es/ei are shaft upper/lower. Negative shaft deviations put the shaft below nominal size.

H8/f7 limit deviations and limit sizes
Nominal
mm
Size interval
mm
H8 hole ES / EI
µm
f7 shaft es / ei
µm
H8 hole limits
mm
f7 shaft limits
mm
10 ↗over 6 up to 10+22 / 0−13 / −2810.000–10.0229.972–9.987
25 ↗over 18 up to 30+33 / 0−20 / −4125.000–25.03324.959–24.980
50 ↗over 30 up to 50+39 / 0−25 / −5050.000–50.03949.950–49.975

Deviations are checked against this site's ISO 286 implementation (dataset ISO 286-1:2010 / ISO 286-2:2010); limit sizes are nominal + deviation / 1000.

At 10 mm: minimum clearance = 0 - (-13) = 13 µm; maximum clearance = +22 - (-28) = 50 µm.

At 25 mm: minimum clearance = 0 - (-20) = 20 µm; maximum clearance = +33 - (-41) = 74 µm. The 25 mm limit sizes are an H8 hole from 25.000 to 25.033 mm and an f7 shaft from 24.959 to 24.980 mm. In millimetres, minimum clearance = 25.000 - 24.980 = 0.020 mm and maximum clearance = 25.033 - 24.959 = 0.074 mm.

At 50 mm: minimum clearance = 0 - (-25) = 25 µm; maximum clearance = +39 - (-50) = 89 µm.

Minimum clearance grows because f7 sits farther below nominal in the larger bands. Maximum clearance grows faster because it includes the H8 hole width and the full f7 zone.

Check the 25 mm example in the calculator ↗

04 / NEARBY FITS

Comparison with neighbouring fits

H7/g6 is a close running fit with less clearance, and H7/h6 can reach zero clearance. H7/js6 and H7/k6 are transition fits, with k6 more interference-biased, and H7/n6 moves further toward interference. H7/p6 is normally a press fit and H7/s6 is heavier. H9/d9 is looser than H8/f7, with a wider hole and a lower shaft. These comparisons are qualitative; the limits at the actual size decide. GB/T 1800.1-2020 is listed by the SAMR national standards catalogue as a modified adoption (MOD) of ISO 286-1:2010; GB/T 1800.2 table values have not been compared on this page and are to be verified.

05 / FREQUENT QUESTIONS

A few details worth getting right

What does H8/f7 mean?

It is a hole-basis fit with an H8 hole and an f7 shaft. The hole lies at or above nominal and the shaft below it.

Is H8/f7 always a clearance fit?

Yes. The H8 lower limit is at nominal size and the f7 upper limit is below it, so the hole is always larger.

Why use H8/f7 instead of H7/g6?

H8/f7 generally gives more running freedom for lubrication, thermal movement and easy assembly. H7/g6 is closer and suits applications needing less play.

Can H8/f7 be used for a plain bearing?

It can be a general running fit, but the correct clearance depends on bearing design, load, speed, lubricant, temperature and shaft material. A supplier recommendation takes precedence.

Does H8/f7 control surface finish or roundness?

No. It controls size only. Surface texture, roundness, cylindricity, alignment and temperature affect running behaviour and need separate specifications.

What happens if the clearance is too large?

Excessive clearance can cause impact, noise, vibration, poor film formation and loss of alignment. Check both clearance extremes against the application.

References & calculation scope

The notation and fit framework follow ISO 286-1:2010; the tabulated tolerance classes and limit deviations are covered by ISO 286-2:2010. Every deviation on this page is generated from, and checked against, the same numerical engine as our calculator.

This independently written guide is not an ISO publication or certification. Examples cover dimensional size limits; they do not select a fit for a particular application.

YOUR SIZE. YOUR LIMITS.

Put a number to the fit.

Enter a basic size from 1 to 500 mm and compare the hole, shaft and clearance limits.

Open the ISO 286 calculator