01 / THE NOTATION

What the fit is

At 10 mm, in the over-6-to-10 mm band, the largest H7 hole and smallest p6 shaft meet line-to-line, so the minimum interference is zero. That boundary is not clearance; this site's calculator reports it as an interference fit, and the ISO 286-1 definition wording is to be verified. At 25 mm and 50 mm the minimum is positive.

H7 has its lower deviation at zero and uses the IT7 width. p6 sits above nominal size with the IT6 width. Interference is positive when the shaft is larger, so i_min = ei - ES and i_max = es - EI.

The p6 zone is above the H7 zone. At 10 mm the zones touch; at 25 mm and 50 mm a gap remains between the hole upper limit and shaft lower limit.

Press-fit behaviour depends on the actual interference, materials, wall thickness, contact length and surface finish. ISO 286 gives size limits, not the joint calculation or assembly procedure.

02 / WHERE IT FITS

Typical uses

H7/p6 is used for parts held without a clamp that tolerate press or thermal assembly: bushings, liners, small hubs, valve seats and similar components needing a firm friction location.

It is not for frequent dismantling, thin walls or joints whose torque capacity is unchecked. Use a key or other positive drive for high or reversing loads.

At the 10 mm boundary, zero minimum interference means the loose extreme may not hold.

03 / WORK IT THROUGH

Limit deviations and worked examples

The table gives limit deviations in micrometres. ES/EI are hole upper/lower deviations; es/ei are shaft upper/lower. Positive interference means the shaft is larger; a negative value would be clearance.

H7/p6 limit deviations and limit sizes
Nominal
mm
Size interval
mm
H7 hole ES / EI
µm
p6 shaft es / ei
µm
H7 hole limits
mm
p6 shaft limits
mm
10 ↗over 6 up to 10+15 / 0+24 / +1510.000–10.01510.015–10.024
25 ↗over 18 up to 30+21 / 0+35 / +2225.000–25.02125.022–25.035
50 ↗over 30 up to 50+25 / 0+42 / +2650.000–50.02550.026–50.042

Deviations are checked against this site's ISO 286 implementation (dataset ISO 286-1:2010 / ISO 286-2:2010); limit sizes are nominal + deviation / 1000.

At 10 mm: minimum interference = +15 - (+15) = 0 µm; maximum interference = +24 - 0 = 24 µm. The zero is the boundary condition of the over-6-to-10 mm band, where the largest hole and smallest shaft are both 10.015 mm.

At 25 mm: minimum interference = +22 - (+21) = 1 µm; maximum interference = +35 - 0 = 35 µm. The 25 mm limit sizes are an H7 hole from 25.000 to 25.021 mm and a p6 shaft from 25.022 to 25.035 mm. In millimetres, minimum interference = 25.022 - 25.021 = 0.001 mm and maximum interference = 25.035 - 25.000 = 0.035 mm.

At 50 mm: minimum interference = +26 - (+25) = 1 µm; maximum interference = +42 - 0 = 42 µm.

Maximum interference uses the largest shaft and smallest hole. Minimum interference is the shaft lower deviation minus the hole upper deviation.

Check the 25 mm example in the calculator ↗

04 / NEARBY FITS

Comparison with neighbouring fits

H7/k6 is a transition fit, and H7/n6 is more interference-biased. H7/p6 is clearly interference at these sizes apart from the zero boundary at 10 mm; H7/s6 is heavier. H7/h6 can reach zero clearance but not interference, H7/g6 is a close running fit, H8/f7 is wider, and H9/d9 is looser. These comparisons are qualitative; the limits at the actual size decide. GB/T 1800.1-2020 is listed by the SAMR national standards catalogue as a modified adoption (MOD) of ISO 286-1:2010; GB/T 1800.2 table values have not been compared on this page and are to be verified.

05 / FREQUENT QUESTIONS

A few details worth getting right

What does H7/p6 mean?

It is a hole-basis fit with an H7 hole and a p6 shaft. The shaft lies above nominal and is normally larger than the hole.

Is H7/p6 always an interference fit?

Yes, if the interference-fit definition includes the limiting case where the largest hole equals the smallest shaft (ISO 286-1 wording to be verified); this site's calculator classes it that way. At 10 mm that limiting case applies: the minimum interference is zero and the parts can meet line-to-line. At 25 mm and 50 mm the minimum is positive.

Why is minimum interference zero at 10 mm?

The H7 upper deviation is +15 µm and the p6 lower deviation is also +15 µm. The largest hole and smallest shaft therefore have the same size.

How is an H7/p6 joint assembled?

It may be pressed, or one part may be heated or cooled to create temporary clearance. Base the method on the calculated interference and a check of contact pressure and material stress.

Does H7/p6 guarantee torque capacity?

No. Torque capacity depends on actual interference, materials, contact length, surface finish and friction. Use a separate joint calculation and add a positive drive where needed.

Does H7/p6 control roundness or surface finish?

No. It controls size only. Form, orientation and surface texture need separate requirements, and temperature, material and assembly method also affect the real fit.

References & calculation scope

The notation and fit framework follow ISO 286-1:2010; the tabulated tolerance classes and limit deviations are covered by ISO 286-2:2010. Every deviation on this page is generated from, and checked against, the same numerical engine as our calculator.

This independently written guide is not an ISO publication or certification. Examples cover dimensional size limits; they do not select a fit for a particular application.

YOUR SIZE. YOUR LIMITS.

Put a number to the fit.

Enter a basic size from 1 to 500 mm and compare the hole, shaft and interference limits.

Open the ISO 286 calculator