01 / THE NOTATION

What the fit is

With H as the hole member, one H7 hole can serve several shaft classes. H7/h6 is a close clearance pair that locates parts well, but it does not guarantee a running clearance or a lubricant film.

In H7/h6, H7 has its lower deviation at zero and h6 has its upper deviation at zero. The shaft cannot exceed nominal size, the hole cannot be smaller, and the tightest combination is line-to-line at nominal size. No permitted combination produces interference.

Zero clearance is possible, not certain. Form, surface texture, temperature and alignment decide whether a real assembly slides; a size calculation alone does not prove it.

The fit family is locational clearance, with light sliding as a secondary use. It is not a transition or interference fit, and it is not a precision running-fit specification: speed, load, lubrication and thermal growth need separate evaluation.

02 / WHERE IT FITS

Typical uses

H7/h6 suits parts that are located accurately but assembled without force: spigots, sliding sleeves, change gears that do not need large clearance, adjustable guides, shaft collars, fixture details and covers. It is also used for hand-fitted parts that move occasionally.

It is less suitable where positive clearance is needed for a lubricant film, thermal expansion may close the clearance, or dirt may damage the surfaces. It is a poor choice for torque transfer without a key or other positive drive.

03 / WORK IT THROUGH

Limit deviations and worked examples

The table gives limit deviations in micrometres. ES/EI are hole upper/lower deviations; es/ei are shaft upper/lower. Clearance is positive when the hole is larger: c_min = EI - es, c_max = ES - ei.

H7/h6 limit deviations and limit sizes
Nominal
mm
Size interval
mm
H7 hole ES / EI
µm
h6 shaft es / ei
µm
H7 hole limits
mm
h6 shaft limits
mm
10 ↗over 6 up to 10+15 / 00 / −910.000–10.0159.991–10.000
25 ↗over 18 up to 30+21 / 00 / −1325.000–25.02124.987–25.000
50 ↗over 30 up to 50+25 / 00 / −1650.000–50.02549.984–50.000

Deviations are checked against this site's ISO 286 implementation (dataset ISO 286-1:2010 / ISO 286-2:2010); limit sizes are nominal + deviation / 1000.

At 10 mm: minimum clearance = 0 - 0 = 0 µm; maximum clearance = +15 - (-9) = 24 µm.

At 25 mm: minimum clearance = 0 - 0 = 0 µm; maximum clearance = +21 - (-13) = 34 µm. The 25 mm limit sizes are an H7 hole from 25.000 to 25.021 mm and an h6 shaft from 24.987 to 25.000 mm. In millimetres, minimum clearance = 25.000 - 25.000 = 0.000 mm and maximum clearance = 25.021 - 24.987 = 0.034 mm.

At 50 mm: minimum clearance = 0 - 0 = 0 µm; maximum clearance = +25 - (-16) = 41 µm.

The minimum is zero at all three sizes because both the H7 lower and h6 upper deviations are zero. Maximum clearance grows with size as both tolerance widths increase.

Check the 25 mm example in the calculator ↗

04 / NEARBY FITS

Comparison with neighbouring fits

H7/g6 keeps a positive clearance for close running, so it is looser than H7/h6 at the tight extreme. H7/js6 and H7/k6 are transition fits, with the k6 zone shifted further toward interference than js6; H7/n6 is more strongly interference-biased, H7/p6 is a press fit, and H7/s6 is heavier. H8/f7 is a running clearance fit with more freedom, and H9/d9 is looser still. These comparisons are qualitative; the limits at the nominal size decide. GB/T 1800.1-2020 is listed by the SAMR national standards catalogue as a modified adoption (MOD) of ISO 286-1:2010; GB/T 1800.2 table values have not been compared on this page and are to be verified.

05 / FREQUENT QUESTIONS

A few details worth getting right

What does H7/h6 mean?

It is a hole-basis fit with an H7 hole and an h6 shaft. The hole lies at or above nominal size and the shaft at or below it.

Is H7/h6 always a clearance fit?

It is a clearance fit, but the minimum can be zero. Interference cannot occur because the hole lower limit and shaft upper limit both sit on the zero line.

Why choose H7/h6 instead of H7/g6?

H7/h6 is tighter at the line-to-line extreme. H7/g6 keeps positive clearance, so it suits free sliding or easier assembly better.

What is the zero-clearance condition?

It occurs when the smallest permitted H7 hole and largest permitted h6 shaft are both at nominal size. Form and surface texture can still prevent free assembly at that limit.

Does H7/h6 control roundness or surface finish?

No. It controls size only. Roundness, cylindricity, straightness, position and surface texture need separate specifications, and temperature and material also affect the real fit.

References & calculation scope

The notation and fit framework follow ISO 286-1:2010; the tabulated tolerance classes and limit deviations are covered by ISO 286-2:2010. Every deviation on this page is generated from, and checked against, the same numerical engine as our calculator.

This independently written guide is not an ISO publication or certification. Examples cover dimensional size limits; they do not select a fit for a particular application.

YOUR SIZE. YOUR LIMITS.

Put a number to the fit.

Enter a basic size from 1 to 500 mm and compare the hole, shaft and clearance limits.

Open the ISO 286 calculator