The engineering workbench / fits and machine elements
DIN 471 External Retaining Rings: Shaft Groove Guide
Look up external / shaft circlip groove diameter, groove width, ring thickness, radial depth and edge distance. The available site tables are GB reference data; DIN 471 equivalence has not been verified.
Exact listed shaft diameters 3–200 mm; committed GB/T 894.1-1986 reference table. No rounding to the next available diameter.
⌀23.9 × 1.3 groove d2 × m, mm · GB/T 894.1-1986 data; schematic, not to scale
02 / Read the limits
Results
Dimensions and deviations in mm. Verification notes apply to the displayed source.
| Characteristic | Result · mm | Interpretation |
|---|---|---|
| Nominal diameter | 25 mm | GB/T 894.1-1986; DIN equivalence NEEDS VERIFICATION. |
| Groove diameter d2 | 23.9 mm | Deviations 0 / -0.21 mm. |
| Groove width m | 1.3 mm | H13; deviations +0.14 / 0 mm. |
| Ring thickness | 1.2 mm | GB reference table, not a verified DIN value. |
| Radial groove depth | 0.55 mm | (d − d2) / 2; calculated. |
| Tabulated groove depth t | Not tabulated | Kept separate from the calculated nominal depth. |
| Minimum edge distance n | 1.7 mm | Source table minimum. |
| Ring diameter (source ring) | 23.2 mm | Source field retained; free/installed diameter definition NEEDS VERIFICATION. |
A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.
GB/T 894.1-1986 A — standard reference table
All dimensions and deviations are in mm. These are GB values; DIN equivalence NEEDS VERIFICATION.
| d | Groove d2 | d2 upper / lower | Width m | m upper / lower | Thickness | Minimum edge n | Verification |
|---|---|---|---|---|---|---|---|
| 3 | 2.8 | 0 / -0.04 | 0.5 | +0.14 / 0 | 0.4 | 0.3 | GB reference; DIN comparison pending |
| 4 | 3.8 | 0 / -0.05 | 0.5 | +0.14 / 0 | 0.4 | 0.3 | GB reference; DIN comparison pending |
| 5 | 4.8 | 0 / -0.05 | 0.7 | +0.14 / 0 | 0.6 | 0.3 | GB reference; DIN comparison pending |
| 6 | 5.7 | 0 / -0.05 | 0.8 | +0.14 / 0 | 0.7 | 0.5 | GB reference; DIN comparison pending |
| 7 | 6.7 | 0 / -0.06 | 0.9 | +0.14 / 0 | 0.8 | 0.5 | GB reference; DIN comparison pending |
| 8 | 7.6 | 0 / -0.06 | 0.9 | +0.14 / 0 | 0.8 | 0.6 | GB reference; DIN comparison pending |
| 9 | 8.6 | 0 / -0.11 | 1.1 | +0.14 / 0 | 1 | 0.6 | GB reference; DIN comparison pending |
| 10 | 9.6 | 0 / -0.11 | 1.1 | +0.14 / 0 | 1 | 0.6 | GB reference; DIN comparison pending |
| 11 | 10.5 | 0 / -0.11 | 1.1 | +0.14 / 0 | 1 | 0.8 | GB reference; DIN comparison pending |
| 12 | 11.5 | 0 / -0.11 | 1.1 | +0.14 / 0 | 1 | 0.8 | GB reference; DIN comparison pending |
| 13 | 12.4 | 0 / -0.11 | 1.1 | +0.14 / 0 | 1 | 0.9 | GB reference; DIN comparison pending |
| 14 | 13.4 | 0 / -0.11 | 1.1 | +0.14 / 0 | 1 | 0.9 | GB reference; DIN comparison pending |
| 15 | 14.3 | 0 / -0.11 | 1.1 | +0.14 / 0 | 1 | 1.1 | GB reference; DIN comparison pending |
| 16 | 15.2 | 0 / -0.11 | 1.1 | +0.14 / 0 | 1 | 1.2 | GB reference; DIN comparison pending |
| 17 | 16.2 | 0 / -0.11 | 1.1 | +0.14 / 0 | 1 | 1.2 | GB reference; DIN comparison pending |
| 18 | 17 | 0 / -0.11 | 1.3 | +0.14 / 0 | 1.2 | 1.5 | GB reference; DIN comparison pending |
| 19 | 18 | 0 / -0.11 | 1.3 | +0.14 / 0 | 1.2 | 1.5 | GB reference; DIN comparison pending |
| 20 | 19 | 0 / -0.13 | 1.3 | +0.14 / 0 | 1.2 | 1.5 | GB reference; DIN comparison pending |
| 21 | 20 | 0 / -0.13 | 1.3 | +0.14 / 0 | 1.2 | 1.5 | GB reference; DIN comparison pending |
| 22 | 21 | 0 / -0.13 | 1.3 | +0.14 / 0 | 1.2 | 1.5 | GB reference; DIN comparison pending |
| 24 | 22.9 | 0 / -0.21 | 1.3 | +0.14 / 0 | 1.2 | 1.7 | GB reference; DIN comparison pending |
| 25 | 23.9 | 0 / -0.21 | 1.3 | +0.14 / 0 | 1.2 | 1.7 | GB reference; DIN comparison pending |
| 26 | 24.9 | 0 / -0.21 | 1.3 | +0.14 / 0 | 1.2 | 1.7 | GB reference; DIN comparison pending |
| 28 | 26.6 | 0 / -0.21 | 1.6 | +0.14 / 0 | 1.5 | 2.1 | GB reference; DIN comparison pending |
| 29 | 27.6 | 0 / -0.21 | 1.6 | +0.14 / 0 | 1.5 | 2.1 | GB reference; DIN comparison pending |
| 30 | 28.6 | 0 / -0.21 | 1.6 | +0.14 / 0 | 1.5 | 2.1 | GB reference; DIN comparison pending |
| 32 | 30.3 | 0 / -0.25 | 1.6 | +0.14 / 0 | 1.5 | 2.6 | GB reference; DIN comparison pending |
| 34 | 32.3 | 0 / -0.25 | 1.6 | +0.14 / 0 | 1.5 | 2.6 | GB reference; DIN comparison pending |
| 35 | 33 | 0 / -0.25 | 1.6 | +0.14 / 0 | 1.5 | 3 | GB reference; DIN comparison pending |
| 36 | 34 | 0 / -0.25 | 1.85 | +0.14 / 0 | 1.75 | 3 | GB reference; DIN comparison pending |
| 38 | 36 | 0 / -0.25 | 1.85 | +0.14 / 0 | 1.7 | 3 | NEEDS VERIFICATION: local thickness 1.75 vs source 1.7 |
| 40 | 37.5 | 0 / -0.25 | 1.85 | +0.14 / 0 | 1.7 | 3.8 | NEEDS VERIFICATION: local thickness 1.75 vs source 1.7 |
| 42 | 39.5 | 0 / -0.25 | 1.85 | +0.14 / 0 | 1.7 | 3.8 | NEEDS VERIFICATION: local thickness 1.75 vs source 1.7 |
| 45 | 42.5 | 0 / -0.25 | 1.85 | +0.14 / 0 | 1.7 | 3.8 | NEEDS VERIFICATION: local thickness 1.75 vs source 1.7 |
| 48 | 45.5 | 0 / -0.25 | 1.85 | +0.14 / 0 | 1.7 | 3.8 | NEEDS VERIFICATION: local thickness 1.75 vs source 1.7 |
| 50 | 47 | 0 / -0.25 | 2.15 | +0.14 / 0 | 2 | 4.5 | GB reference; DIN comparison pending |
| 52 | 49 | 0 / -0.25 | 2.15 | +0.14 / 0 | 2 | 4.5 | GB reference; DIN comparison pending |
| 55 | 52 | 0 / -0.3 | 2.15 | +0.14 / 0 | 2 | 4.5 | GB reference; DIN comparison pending |
| 56 | 53 | 0 / -0.3 | 2.15 | +0.14 / 0 | 2 | 4.5 | GB reference; DIN comparison pending |
| 58 | 55 | 0 / -0.3 | 2.15 | +0.14 / 0 | 2 | 4.5 | GB reference; DIN comparison pending |
| 60 | 57 | 0 / -0.3 | 2.15 | +0.14 / 0 | 2 | 4.5 | GB reference; DIN comparison pending |
| 62 | 59 | 0 / -0.3 | 2.15 | +0.14 / 0 | 2 | 4.5 | GB reference; DIN comparison pending |
| 63 | 60 | 0 / -0.3 | 2.15 | +0.14 / 0 | 2 | 4.5 | GB reference; DIN comparison pending |
| 65 | 62 | 0 / -0.3 | 2.65 | +0.14 / 0 | 2.5 | 4.5 | GB reference; DIN comparison pending |
| 68 | 65 | 0 / -0.3 | 2.65 | +0.14 / 0 | 2.5 | 4.5 | GB reference; DIN comparison pending |
| 70 | 67 | 0 / -0.3 | 2.65 | +0.14 / 0 | 2.5 | 4.5 | GB reference; DIN comparison pending |
| 72 | 69 | 0 / -0.3 | 2.65 | +0.14 / 0 | 2.5 | 4.5 | GB reference; DIN comparison pending |
| 75 | 72 | 0 / -0.3 | 2.65 | +0.14 / 0 | 2.5 | 4.5 | GB reference; DIN comparison pending |
| 78 | 75 | 0 / -0.3 | 2.65 | +0.14 / 0 | 2.5 | 4.5 | GB reference; DIN comparison pending |
| 80 | 76.5 | 0 / -0.3 | 2.65 | +0.14 / 0 | 2.5 | 5.3 | GB reference; DIN comparison pending |
| 82 | 78.5 | 0 / -0.3 | 2.65 | +0.14 / 0 | 2.5 | 5.3 | GB reference; DIN comparison pending |
| 85 | 81.5 | 0 / -0.35 | 3.15 | +0.14 / 0 | 3 | 5.3 | GB reference; DIN comparison pending |
| 88 | 84.5 | 0 / -0.35 | 3.15 | +0.14 / 0 | 3 | 5.3 | GB reference; DIN comparison pending |
| 90 | 86.5 | 0 / -0.35 | 3.15 | +0.14 / 0 | 3 | 5.3 | GB reference; DIN comparison pending |
| 95 | 91.5 | 0 / -0.35 | 3.15 | +0.14 / 0 | 3 | 5.3 | GB reference; DIN comparison pending |
| 100 | 96.5 | 0 / -0.35 | 3.15 | +0.14 / 0 | 3 | 5.3 | GB reference; DIN comparison pending |
| 105 | 101 | 0 / -0.54 | 4.15 | +0.18 / 0 | 4 | 6 | GB reference; DIN comparison pending |
| 110 | 106 | 0 / -0.54 | 4.15 | +0.18 / 0 | 4 | 6 | GB reference; DIN comparison pending |
| 115 | 111 | 0 / -0.54 | 4.15 | +0.18 / 0 | 4 | 6 | GB reference; DIN comparison pending |
| 120 | 116 | 0 / -0.54 | 4.15 | +0.18 / 0 | 4 | 6 | GB reference; DIN comparison pending |
| 125 | 121 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 6 | GB reference; DIN comparison pending |
| 130 | 126 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 6 | GB reference; DIN comparison pending |
| 135 | 131 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 6 | GB reference; DIN comparison pending |
| 140 | 136 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 6 | GB reference; DIN comparison pending |
| 145 | 141 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 6 | GB reference; DIN comparison pending |
| 150 | 145 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 7.5 | GB reference; DIN comparison pending |
| 155 | 150 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 7.5 | GB reference; DIN comparison pending |
| 160 | 155 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 7.5 | GB reference; DIN comparison pending |
| 165 | 160 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 7.5 | GB reference; DIN comparison pending |
| 170 | 165 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 7.5 | GB reference; DIN comparison pending |
| 175 | 170 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 7.5 | GB reference; DIN comparison pending |
| 180 | 175 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 7.5 | GB reference; DIN comparison pending |
| 185 | 180 | 0 / -0.63 | 4.15 | +0.18 / 0 | 4 | 7.5 | GB reference; DIN comparison pending |
| 190 | 185 | 0 / -0.72 | 4.15 | +0.18 / 0 | 4 | 7.5 | GB reference; DIN comparison pending |
| 195 | 190 | 0 / -0.72 | 4.15 | +0.18 / 0 | 4 | 7.5 | GB reference; DIN comparison pending |
| 200 | 195 | 0 / -0.72 | 4.15 | +0.18 / 0 | 4 | 7.5 | GB reference; DIN comparison pending |
03 / How to use
How to use this calculator
- This calculator shows GB reference shaft-groove dimensions from the site's Chinese tool. DIN 471 values are to be verified; check a DIN 471 table or the ring maker's catalogue before machining.
- Enter the nominal shaft diameter from the drawing. Only exact listed sizes are accepted; there is no interpolation.
- There is no ring-type selector for shaft rings on this page; the listed sizes form the only series offered.
- Read the ring and shaft-groove values from the result, including the groove dimensions and the ring size.
- Check the drawing for the groove position, ring orientation, material and any individual requirement before machining or assembly.
Table lookup, with explicit boundaries
Calculated nominal groove depth = (d − d2) / 2.
Groove diameter and width limits = nominal value + its listed deviation.
Circlip sizes are discrete catalogue entries, not continuous intervals. An unlisted input is rejected. A gap in the list does not license interpolation. Missing source fields remain “Not tabulated”.
04 / Engineering context
DIN 471 External Retaining Rings: Circlips for Shafts
DIN 471 covers external retaining rings, commonly called circlips, for shafts. The ring is expanded, moved along the shaft and allowed to spring into a circumferential groove. The part that remains proud of the shaft forms a removable shoulder that can locate a bearing, gear, pulley, collar or similar component. It is an axial-retention device, not a coupling: it does not transmit torque and should not be used as a drive element.
The groove is machined into the shaft and is part of the retaining system. Its diameter, width, profile and position relative to the shoulder are matched to the ring. A groove that is too shallow or wrongly formed may prevent the ring from seating fully, while an oversize groove can allow unwanted axial movement. The ring must be free to expand during fitting and then sit completely in the groove. Follow the standard and drawing rather than cutting the groove by eye.
On this page, the calculator looks up the site's GB reference ring and shaft-groove data for an exact listed shaft diameter; DIN 471 dimensions have not been verified against that table and are to be verified. The result includes the groove diameter and width with their deviations, the ring thickness, the radial groove depth and the minimum edge distance. Use the result with the standard edition, ring type and installation direction specified for the job. The reference table below lists the GB values; DIN 471 ring and groove sizes are not reproduced because they have not been verified.
GB / DIN comparison status
| Reference | Status |
|---|---|
| GB/T 894.1-1986 | Committed Chinese site data used for the reference calculator. |
| GB/T 894-2017 | Working page relabels data “GB/T 894.1-2017”; exact designation and five thickness edits NEEDS VERIFICATION. Not adopted here. |
| DIN 471 | NEEDS VERIFICATION: independent dimensions, tolerances and interchangeability are not provided by the site. |
Source: Chinese retaining-ring tool. Missing load ratings are not filled; this calculator performs no load-capacity selection.
06 / Questions
Frequently asked questions
What is DIN 471?
DIN 471 is the German standard for external retaining rings, or circlips, used on shafts. The ring fits into a groove on the outside of the shaft and provides a shoulder for axially locating a component. It is distinct from a threaded nut, a collar or a shaft shoulder because it is removable and occupies a relatively narrow groove.
Where is the groove for a DIN 471 ring?
The groove is cut into the outside diameter of the shaft, close to the shoulder or component it is meant to retain. The ring expands over the shaft, then contracts into the groove. The groove's diameter, width, profile and edge distance are all part of the retaining-ring design, not arbitrary features.
What does the calculator look up for DIN 471?
It looks up GB reference ring and shaft-groove values for the exact listed shaft diameter you enter; DIN 471 equivalence is to be verified. The result identifies the applicable ring size and gives the groove data needed to machine and check the shaft. Exact fields depend on the calculator version, so read the labels in the result rather than assuming a particular output.
What is the difference between DIN 471 and DIN 472?
DIN 471 is for external rings on shafts: the ring sits in a groove on the shaft and protrudes outward. DIN 472 is for internal rings in bores or housings: the ring sits in a groove inside the bore and protrudes inward. The two use different groove geometry and different installation directions, so a 471 ring should not be substituted for a 472 ring or vice versa.
Does a DIN 471 ring transmit torque?
No. A DIN 471 ring is intended for axial retention. It may resist an axial force up to the capacity of the ring and groove, but it is not a torque-transmitting element and should not be relied on to drive a hub. Torque must be carried by a key, spline, friction fit or another appropriate connection.
Can a DIN 471 ring be reused?
Reuse depends on the ring material, how far it was expanded during removal, whether it was deformed, and the manufacturer's guidance. A ring that has been over-expanded, bent or corroded should be replaced. For critical assemblies, fit a new ring and confirm that it seats fully in the groove.
Which way should a DIN 471 ring face?
Retaining rings can have a defined installation direction, and the ring's edge geometry may be designed to bear against the retained part in a particular way. Follow the standard, catalogue and manufacturer's instructions for the specific ring. Do not assume that a ring can be flipped without consequence, especially where axial load or high speed is involved.
Does shaft diameter alone define the complete DIN 471 joint?
No. The shaft diameter selects the standard ring and groove size, but the joint also depends on the groove form, ring type, material, retained component, axial load, speed and assembly method. Confirm the full callout and verify the groove before fitting the ring. The calculator supplies the dimensional lookup, not a validation of the whole assembly.