EngineeringFits中文 / Chinese version ↗

The engineering workbench / fits and machine elements

Parallel Keyways: DIN 6885, ISO/R 773 and GB/T 1095

Find parallel key b × h, shaft groove depth t1, hub groove depth t2, groove-width deviations and the dimensions d − t1 and d + t2.

GB/T 1095-2003 dimensions from the committed Chinese tool, shaft diameters 6–500 mm. DIN 6885-1 / ISO R773 comparison is pending; no interchangeable dimensions are asserted.

SECTION · GB/T 1095-2003⌀25 mm shaft
Parallel key and keyway section for a 25 mm shaftCross-section through a 25 mm shaft and its hub with a 8 by 7 mm parallel key. The key width b is 8 mm, the shaft keyway depth t1 is 4 mm and the hub keyway depth t2 is 3.3 mm, from the GB/T 1095-2003 table used by this page. Proportions follow these values.b = 8t2 = 3.3t1 = 4⌀d = 25HubShaft

8 × 7 key b × h, mm · GB/T 1095-2003 data; DIN 6885-1 to be verified

02 / Read the limits

Results

Dimensions and deviations in mm. Verification notes apply to the displayed source.

CharacteristicResult · mmInterpretation
Key b × h8 × 7 mmNominal parallel-key section.
Shaft groove depth t14 mmDepth allowance +0.2 / 0 mm in the source.
Hub groove depth t23.3 mmDepth allowance +0.2 / 0 mm in the source.
Shaft dimension d − t121 mmDeviation 0 / −0.2 mm on this dimension.
Hub dimension d + t228.3 mmDeviation +0.2 / 0 mm on this dimension.
Shaft groove width N90 / -0.036 mmUpper / lower deviations from nominal b.
Hub groove width JS9+0.018 / -0.018 mmUpper / lower deviations from nominal b.
Groove root radius0.25–0.4 mmTabulated minimum–maximum.

A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.

Parallel key and groove dimensions

Shaft d · mm (upper inclusive)Key b × h · mmt1 · mmt2 · mmDepth allowances t1 / t2 · mmRoot radius · mm
≥6 to ≤82 × 21.21+0.1/0; +0.1/00.08–0.16
>8 to ≤103 × 31.81.4+0.1/0; +0.1/00.08–0.16
>10 to ≤124 × 42.51.8+0.1/0; +0.1/00.16–0.25
>12 to ≤175 × 532.3+0.1/0; +0.1/00.16–0.25
>17 to ≤226 × 63.52.8+0.1/0; +0.1/00.16–0.25
>22 to ≤308 × 743.3+0.2/0; +0.2/00.25–0.4
>30 to ≤3810 × 853.3+0.2/0; +0.2/00.25–0.4
>38 to ≤4412 × 853.3+0.2/0; +0.2/00.25–0.4
>44 to ≤5014 × 95.53.8+0.2/0; +0.2/00.25–0.4
>50 to ≤5816 × 1064.3+0.2/0; +0.2/00.25–0.4
>58 to ≤6518 × 1174.4+0.2/0; +0.2/00.25–0.4
>65 to ≤7520 × 127.54.9+0.2/0; +0.2/00.4–0.6
>75 to ≤8522 × 1495.4+0.2/0; +0.2/00.4–0.6
>85 to ≤9525 × 1495.4+0.2/0; +0.2/00.4–0.6
>95 to ≤11028 × 16106.4+0.2/0; +0.2/00.4–0.6
>110 to ≤13032 × 18117.4+0.3/0; +0.3/00.7–1
>130 to ≤15036 × 20128.4+0.3/0; +0.3/00.7–1
>150 to ≤17040 × 22139.4+0.3/0; +0.3/00.7–1
>170 to ≤20045 × 251510.4+0.3/0; +0.3/00.7–1
>200 to ≤23050 × 281711.4+0.3/0; +0.3/00.7–1
>230 to ≤26056 × 322012.4+0.3/0; +0.3/01.2–1.6
>260 to ≤29063 × 322012.4+0.3/0; +0.3/01.2–1.6
>290 to ≤33070 × 362214.4+0.3/0; +0.3/01.2–1.6
>330 to ≤38080 × 402515.4+0.3/0; +0.3/02–2.5
>380 to ≤44090 × 452817.4+0.3/0; +0.3/02–2.5
>440 to ≤500100 × 503119.5+0.3/0; +0.3/02–2.5

Groove-width deviations

All entries are upper / lower deviations in mm from nominal key width b. This is the groove width, not the key’s own width tolerance.

b · mmH9D10N9JS9P9
2+0.025 / 0+0.06 / +0.02-0.004 / -0.029+0.0125 / -0.0125-0.006 / -0.031
3+0.025 / 0+0.06 / +0.02-0.004 / -0.029+0.0125 / -0.0125-0.006 / -0.031
4+0.03 / 0+0.078 / +0.030 / -0.03+0.015 / -0.015-0.012 / -0.042
5+0.03 / 0+0.078 / +0.030 / -0.03+0.015 / -0.015-0.012 / -0.042
6+0.03 / 0+0.078 / +0.030 / -0.03+0.015 / -0.015-0.012 / -0.042
8+0.036 / 0+0.098 / +0.040 / -0.036+0.018 / -0.018-0.015 / -0.051
10+0.036 / 0+0.098 / +0.040 / -0.036+0.018 / -0.018-0.015 / -0.051
12+0.043 / 0+0.12 / +0.050 / -0.043+0.0215 / -0.0215-0.018 / -0.061
14+0.043 / 0+0.12 / +0.050 / -0.043+0.0215 / -0.0215-0.018 / -0.061
16+0.043 / 0+0.12 / +0.050 / -0.043+0.0215 / -0.0215-0.018 / -0.061
18+0.043 / 0+0.12 / +0.050 / -0.043+0.0215 / -0.0215-0.018 / -0.061
20+0.052 / 0+0.149 / +0.0650 / -0.052+0.026 / -0.026-0.022 / -0.074
22+0.052 / 0+0.149 / +0.0650 / -0.052+0.026 / -0.026-0.022 / -0.074
25+0.052 / 0+0.149 / +0.0650 / -0.052+0.026 / -0.026-0.022 / -0.074
28+0.052 / 0+0.149 / +0.0650 / -0.052+0.026 / -0.026-0.022 / -0.074
32+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
36+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
40+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
45+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
50+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
56+0.074 / 0+0.22 / +0.10 / -0.074+0.037 / -0.037-0.032 / -0.106
63+0.074 / 0+0.22 / +0.10 / -0.074+0.037 / -0.037-0.032 / -0.106
70+0.074 / 0+0.22 / +0.10 / -0.074+0.037 / -0.037-0.032 / -0.106
80+0.087 / 0+0.26 / +0.120 / -0.087+0.0435 / -0.0435-0.037 / -0.124
90+0.087 / 0+0.26 / +0.120 / -0.087+0.0435 / -0.0435-0.037 / -0.124
100+0.087 / 0+0.26 / +0.120 / -0.087+0.0435 / -0.0435-0.037 / -0.124

03 / How to use

How to use this calculator

  1. This calculator uses the GB/T 1095-2003 keyway table from the site's Chinese tool. DIN 6885-1 and ISO/R 773 values have not been verified against it, so confirm the standard named on the drawing first.
  2. Enter the nominal shaft diameter. Use the drawing value, not a caliper reading from a worn shaft.
  3. Choose the connection (loose, normal or tight); it sets the shaft and hub groove-width tolerance codes.
  4. Read the key cross-section, shaft keyway, hub keyway and tolerance values from the result. Do not substitute a value remembered from another diameter or standard.
  5. Check the drawing for any individual keyway note, fit or material requirement. An explicit requirement takes precedence over the general lookup.

Table lookup, with explicit boundaries

Select the shaft-diameter interval → read b, h, t1 and t2.
Shaft dimension = d − t1, with deviation 0 / −t1 allowance.
Hub dimension = d + t2, with deviation +t2 allowance / 0.
Groove-width deviations apply to nominal b, not shaft diameter d.

The source accepts 6 mm in its first interval (6–8 mm). Following intervals exclude the lower endpoint and include the upper endpoint. In particular, 30 mm uses the >22–30 mm row. Inputs outside 6–500 mm are rejected.

04 / Engineering context

Parallel-Key Keyways: How DIN 6885, ISO/R 773 and GB/T 1095 Relate

A parallel key is a rectangular or square piece that sits in a keyway cut into a shaft and in a matching keyway in the hub. Its job is to transmit torque between the two parts while still allowing them to be assembled and, in many designs, slid axially. The keyway is therefore more than a slot. Its width, depth, edge condition and fit determine how the key seats, how the load is shared, and how much material is removed from the shaft.

Several standards describe this family. DIN 6885-1 covers parallel keys and their keyways. ISO/R 773 is an older international recommendation for rectangular or square parallel keys and corresponding keyways. The Chinese national standards catalogue (SAMR) lists GB/T 1095-2003 as a non-equivalent (NEQ) adoption of ASME B18.25.1M:1996; any relationship to ISO/R 773 is to be verified, and separate editions can still differ in detail. The three share the same basic geometry and size logic, but they are separate documents with their own editions, scopes and tolerance details. A familiar-looking nominal key does not make every callout automatically interchangeable; the drawing, purchase order and named edition decide.

Shaft diameter is the starting point because the standards use it to select the nominal key cross-section and the corresponding shaft and hub keyway dimensions. Those values are tabulated rather than calculated from a simple formula, so the calculator on this page performs the lookup for the diameter you enter. It returns the GB/T 1095-2003 key and keyway values for that size, including the width, height, depths and tolerances that apply to that size. Key length, fit choice, material and allowable torque remain separate design decisions.

GB / DIN / ISO comparison status

StandardData used / status
GB/T 1095-2003Committed /keyway/ dimensions and width-tolerance values.
DIN 6885-1NEEDS VERIFICATION: no independent DIN table in the site dataset.
ISO R773NEEDS VERIFICATION: dimensional relationship and edition must be checked.

No numerical DIN-versus-GB differences are inferred. Source: Chinese GB/T 1095 tool.

06 / Questions

Frequently asked questions

What is a parallel keyway?

A parallel keyway is the slot that accepts a parallel key. One slot is machined in the shaft and a matching slot in the hub. The key bears against the sides of both slots to transmit torque, while the fit at the top and bottom controls how it seats. The arrangement is intended for torque transfer and axial location of the hub, not for pulling two parts together.

What is the difference between DIN 6885, ISO/R 773 and GB/T 1095?

DIN 6885-1 is the German standard for parallel keys and keyways. ISO/R 773 is an older international recommendation covering rectangular or square parallel keys and their keyways. The Chinese national standards catalogue (SAMR) lists GB/T 1095-2003 as a non-equivalent (NEQ) adoption of ASME B18.25.1M:1996; any relationship to ISO/R 773 is to be verified, and separate editions can still differ in detail. They are related documents, but each has its own edition and scope, so the named standard still controls the job.

How does shaft diameter select the key and keyway?

The standards group shaft diameters into bands and assign a nominal key cross-section to each band. That cross-section then links to the shaft and hub keyway dimensions. Because the relationship is tabulated, a nearby diameter can fall in a different band. Enter the exact nominal diameter on the drawing and read the result from the calculator rather than estimating the key size.

Are the three standards interchangeable at the bench?

No. Comparable geometry does not prove that every dimension and tolerance is identical across editions. The Chinese national standards catalogue (SAMR) lists GB/T 1095-2003 as a non-equivalent (NEQ) adoption of ASME B18.25.1M:1996; any relationship to ISO/R 773 is to be verified, and separate editions can still differ in detail. If a replacement key is being made for an existing assembly, identify the original callout and check the measured keyway before cutting metal.

Which values does the calculator return?

The calculator returns the GB/T 1095-2003 key and keyway values for the entered shaft diameter. That includes the nominal key width and height, the shaft keyway depth, the hub keyway depth the groove-width deviations for the chosen connection and the groove root radius. DIN 6885-1 and ISO/R 773 values are not shown and are to be verified. Read the exact fields shown in the result; the reference table on this page lists every diameter band.

Does a keyway weaken the shaft?

A keyway removes material and introduces edges where stress can concentrate, so it affects the shaft's strength and fatigue behaviour. The effect depends on the shaft material, heat treatment, surface condition, keyway geometry, load type and the rest of the shaft design. A standard lookup gives the dimensions, not a strength approval. Check highly loaded or reversing-duty shafts with a competent engineer.

Can I choose the key length from the shaft diameter alone?

No. The key cross-section is linked to shaft diameter, but key length depends on the hub length, the torque to be carried, the permissible bearing pressure, the key material and the assembly arrangement. The calculator result covers the section lookup; set the length from the drawing or a separate design check. If the drawing gives no length, confirm it rather than assuming that any standard length will do.