The engineering workbench / fits and machine elements
Metric Tap Drill Sizes: Choosing the Right Core Hole
Estimate a cutting-tap drill as nominal thread diameter D minus pitch P. Compare that estimate with provisional manufacturer chart drills for selected metric coarse and fine threads.
Selected candidate ISO 261/262 metric pitch series only. Pitch assignments, chart drill sizes and all minor-diameter limits NEEDS VERIFICATION. Forming taps are outside this calculator.
6.75 mm D − P estimate · *chart drill 6.8 mm, provisional, to be verified
02 / Read the limits
Results
Dimensions and deviations in mm. Verification notes apply to the displayed source.
| Characteristic | Result · mm | Interpretation |
|---|---|---|
| Thread D × P | 8 × 1.25 mm | coarse; pitch series NEEDS VERIFICATION against ISO 261/262. |
| Cutting-tap estimate D − P | 6.75 mm | Approximation; excludes forming taps. |
| Provisional chart drill | 6.8 mm | NEEDS VERIFICATION against ISO 2306 / DIN 336; manufacturer-specific. |
| Minor-diameter limits | NEEDS VERIFICATION | Not supplied; no tolerance class or limits inferred from D − P. |
A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.
Selected coarse and fine pitch table — NEEDS VERIFICATION
| Thread | Series | Pitch · mm | D − P estimate · mm | Provisional chart drill · mm | Minor limits / status |
|---|---|---|---|---|---|
| M3 × 0.5 | coarse | 0.5 | 2.5 | 2.5 | Unavailable — NEEDS VERIFICATION |
| M4 × 0.7 | coarse | 0.7 | 3.3 | 3.3 | Unavailable — NEEDS VERIFICATION |
| M5 × 0.8 | coarse | 0.8 | 4.2 | 4.2 | Unavailable — NEEDS VERIFICATION |
| M6 × 1 | coarse | 1 | 5 | 5 | Unavailable — NEEDS VERIFICATION |
| M8 × 1.25 | coarse | 1.25 | 6.75 | 6.8 | Unavailable — NEEDS VERIFICATION |
| M10 × 1.25 | fine | 1.25 | 8.75 | 8.7 | Unavailable — NEEDS VERIFICATION |
| M10 × 1.5 | coarse | 1.5 | 8.5 | 8.5 | Unavailable — NEEDS VERIFICATION |
| M12 × 1.25 | fine | 1.25 | 10.75 | 10.8 | Unavailable — NEEDS VERIFICATION |
| M12 × 1.75 | coarse | 1.75 | 10.25 | 10.2 | Unavailable — NEEDS VERIFICATION |
| M16 × 1.5 | fine | 1.5 | 14.5 | 14.5 | Unavailable — NEEDS VERIFICATION |
| M16 × 2 | coarse | 2 | 14 | 14 | Unavailable — NEEDS VERIFICATION |
| M20 × 1.5 | fine | 1.5 | 18.5 | 18.5 | Unavailable — NEEDS VERIFICATION |
| M20 × 2.5 | coarse | 2.5 | 17.5 | 17.5 | Unavailable — NEEDS VERIFICATION |
| M24 × 2 | fine | 2 | 22 | 22 | Unavailable — NEEDS VERIFICATION |
| M24 × 3 | coarse | 3 | 21 | 21 | Unavailable — NEEDS VERIFICATION |
03 / How to use
How to use this calculator
- Read the drawing callout and note the pitch after the × sign. The pitch after the × sign must match the calculator selection; do not choose by nominal diameter alone.
- Select the exact designation from the thread presets (coarse and selected fine pitches), or enter D and P for a custom pair.
- Read the D − P cutting-tap estimate and the provisional chart drill (to be verified). The calculator has no material or tap-type input. Note the assumptions behind the result, because a value taken from different conditions may not apply.
- Read the drill size from the result. Do not substitute a value from another thread, material or tap type.
- For a blind hole, provide enough drill depth for the tap chamfer and chip clearance, and specify thread depth separately from drill depth.
- Check the finished thread with the specified gauge and, for critical work, against the tap manufacturer's recommendation.
Table lookup, with explicit boundaries
Example: M8 × 1.25 → 8 − 1.25 = 6.75 mm (estimate).
The separate 6.8 mm manufacturer chart entry is provisional; it is not obtained by silently rounding every D − P result.
Minor-diameter limits are unavailable and are not derived from this formula.
Thread entries are selected discrete diameter/pitch pairs, not continuous standard ranges. Custom positive inputs with D > P are allowed for the formula only. A custom pair without chart data shows “Not tabulated”.
04 / Engineering context
Metric Tap Drill Sizes: How to Choose a Core Hole Before Tapping
A tap drill is the drill that produces the core hole before a thread is cut or formed. On a metric drawing, the starting point is the thread designation: the M callout gives the nominal diameter, and the number after the × sign gives the pitch. For the coarse series, that pitch is fixed for each nominal size, so a coarse M8 callout and a fine M8 callout are not interchangeable even though both begin with M8. The core hole has to suit the actual callout, not a generic M8 label.
The size of that core hole also depends on the intended thread engagement. A hole toward the small end leaves more material for the tap and produces a fuller thread, but it raises cutting torque and the risk of tap breakage. A hole toward the large end makes tapping easier but removes engagement from the finished joint. The right balance depends on the tap type, workpiece material, hole depth and the tolerance class required by the drawing. Workshop practice varies, so a drill that works well in one shop's aluminum fixture may not be the best choice in stainless steel on another machine.
ISO metric thread standards describe the thread rather than a single workshop drill choice. ISO 68-1 defines the basic and design profiles, ISO 262 selects common fastener sizes and pitches, and ISO 724 gives basic thread dimensions. A tap drill is tooling, not a thread dimension, and cutting taps, forming taps and different materials can call for different core holes. Read the size from the calculator on this page for the exact designation and tap setting, then check the tap manufacturer's data for critical or high-volume work.
Thread data sources and verification
Pitch and drill candidates were transcribed from the Tapmatic manufacturer chart; the M8 × 1.25 drill is from the Guhring SuperLine catalogue. Tapmatic’s chart assumes job drills cutting about 0.003 inch oversize. Manufacturer choices can differ.
NEEDS VERIFICATION: selected pitches against ISO 261 / ISO 262; recommended drills against ISO 2306 / DIN 336; minor-diameter limits against the specified thread tolerance standard and class. No minor-diameter limits are supplied.
06 / Questions
Frequently asked questions
What is a tap drill?
A tap drill is the drill used to make the core hole before tapping. It is not a clearance drill and it is not the final thread size. Its diameter controls how much material the tap cuts or forms and therefore affects torque, chip load, thread engagement and the risk of tap breakage.
Why is there no single drill diameter for every job?
Because a single diameter would not cover every tap, material, hole type and engagement target. The calculator gives a D − P estimate and a provisional chart drill for the designation; it does not adjust for tap type or material. A shop standard or tap manufacturer's table may differ, so confirm before production.
Does the pitch in the callout matter?
Yes. A coarse thread and a fine thread of the same nominal size have different pitches and different core-hole requirements. Use the complete designation, including the pitch, when you select the thread in the calculator.
Does workpiece material change the tap drill?
It can. Ductile materials, work-hardening grades, abrasive alloys and different chip-forming behavior all influence how a tap performs. A size that gives good results in one material may need a different tap style or a different core hole in another. Follow the tap maker's data when it is available.
Are forming taps treated the same as cutting taps?
No. Cutting taps remove material; forming taps displace it. Forming taps need a precise core hole and good lubrication, and they are not suitable for every material. Do not reuse a cutting-tap result for a forming tap; confirm the forming-tap hole with the tap maker.
How does thread engagement affect the choice?
A tighter core hole leaves more material for the thread and can increase engagement, but it also raises torque and breakage risk. A more open hole reduces tapping load but lowers engagement. The design should state the engagement the joint needs, and the shop should work within the tap maker's range rather than choosing by feel.
Can I use an imperial drill that is close in size?
No. A nearest imperial drill is not the same as the metric core hole, and the small difference can matter, especially in small threads. Use a metric drill of the specified size or the exact equivalent allowed by your procedure, and account for the drill's actual tolerance.
Is the calculator a substitute for a tap manufacturer's data?
It is a starting point for the core-hole size, not a guarantee of tapping performance. For safety-critical, high-volume or difficult materials, confirm the result against the tap manufacturer's recommendation and prove the process on the actual workpiece.