The engineering workbench / fits and machine elements
M12 × 1.75 Tap Drill: Core Hole for Metric Coarse Thread
Estimate a cutting-tap drill as nominal thread diameter D minus pitch P. Compare that estimate with provisional manufacturer chart drills for selected metric coarse and fine threads.
Selected candidate ISO 261/262 metric pitch series only. Pitch assignments, chart drill sizes and all minor-diameter limits NEEDS VERIFICATION. Forming taps are outside this calculator.
10.25 mm D − P estimate · *chart drill 10.2 mm, provisional, to be verified
02 / Read the limits
Results
Dimensions and deviations in mm. Verification notes apply to the displayed source.
| Characteristic | Result · mm | Interpretation |
|---|---|---|
| Thread D × P | 12 × 1.75 mm | coarse; pitch series NEEDS VERIFICATION against ISO 261/262. |
| Cutting-tap estimate D − P | 10.25 mm | Approximation; excludes forming taps. |
| Provisional chart drill | 10.2 mm | NEEDS VERIFICATION against ISO 2306 / DIN 336; manufacturer-specific. |
| Minor-diameter limits | NEEDS VERIFICATION | Not supplied; no tolerance class or limits inferred from D − P. |
A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.
Selected coarse and fine pitch table — NEEDS VERIFICATION
| Thread | Series | Pitch · mm | D − P estimate · mm | Provisional chart drill · mm | Minor limits / status |
|---|---|---|---|---|---|
| M3 × 0.5 | coarse | 0.5 | 2.5 | 2.5 | Unavailable — NEEDS VERIFICATION |
| M4 × 0.7 | coarse | 0.7 | 3.3 | 3.3 | Unavailable — NEEDS VERIFICATION |
| M5 × 0.8 | coarse | 0.8 | 4.2 | 4.2 | Unavailable — NEEDS VERIFICATION |
| M6 × 1 | coarse | 1 | 5 | 5 | Unavailable — NEEDS VERIFICATION |
| M8 × 1.25 | coarse | 1.25 | 6.75 | 6.8 | Unavailable — NEEDS VERIFICATION |
| M10 × 1.25 | fine | 1.25 | 8.75 | 8.7 | Unavailable — NEEDS VERIFICATION |
| M10 × 1.5 | coarse | 1.5 | 8.5 | 8.5 | Unavailable — NEEDS VERIFICATION |
| M12 × 1.25 | fine | 1.25 | 10.75 | 10.8 | Unavailable — NEEDS VERIFICATION |
| M12 × 1.75 | coarse | 1.75 | 10.25 | 10.2 | Unavailable — NEEDS VERIFICATION |
| M16 × 1.5 | fine | 1.5 | 14.5 | 14.5 | Unavailable — NEEDS VERIFICATION |
| M16 × 2 | coarse | 2 | 14 | 14 | Unavailable — NEEDS VERIFICATION |
| M20 × 1.5 | fine | 1.5 | 18.5 | 18.5 | Unavailable — NEEDS VERIFICATION |
| M20 × 2.5 | coarse | 2.5 | 17.5 | 17.5 | Unavailable — NEEDS VERIFICATION |
| M24 × 2 | fine | 2 | 22 | 22 | Unavailable — NEEDS VERIFICATION |
| M24 × 3 | coarse | 3 | 21 | 21 | Unavailable — NEEDS VERIFICATION |
03 / How to use
How to use this calculator
- Confirm that the drawing specifies M12 × 1.75 and not another M12 pitch.
- Select the M12 × 1.75 — coarse preset in the calculator (it is preselected on this page), or enter D and P directly.
- The calculator has no tap-type or material input; it shows a D − P cutting-tap estimate and a provisional manufacturer chart drill (to be verified), and note whether the operation will be hand or machine tapping.
- Read the drill size from the result and keep it with the conditions used.
- For a blind hole, add depth for the tap chamfer and chips, and specify thread depth separately.
- Check the thread with the specified gauge and inspect the hole position before assembly.
Table lookup, with explicit boundaries
Example: M8 × 1.25 → 8 − 1.25 = 6.75 mm (estimate).
The separate 6.8 mm manufacturer chart entry is provisional; it is not obtained by silently rounding every D − P result.
Minor-diameter limits are unavailable and are not derived from this formula.
Thread entries are selected discrete diameter/pitch pairs, not continuous standard ranges. Custom positive inputs with D > P are allowed for the formula only. A custom pair without chart data shows “Not tabulated”.
04 / Engineering context
M12 × 1.75 Tap Drill: Core Hole for a Metric Coarse Thread
M12 × 1.75 is the ISO metric coarse thread for M12 fasteners. It is used on clamps, mounts, machine connections and fixtures where a larger fastener is needed without moving to the heavy M16 and M20 range. Read the core-hole size from the calculator for M12 × 1.75; the pitch must match the drawing callout.
At this size, tapping is often done on a machine, and the setup begins to dominate the result. Spindle alignment, fixture rigidity, tap holder condition and chip evacuation all affect whether the finished thread is clean and on size. The core hole still has a direct effect on torque and engagement, so it should not be chosen only to make the tap turn easily.
Blind holes need a depth plan that accounts for the tap chamfer, chips and the risk of bottoming out. Through holes are simpler but still need support at breakthrough to avoid burrs or an oversized exit. Use the calculator for the M12 × 1.75 core hole, then confirm the tap and cutting data against the manufacturer's recommendation for the material.
Thread data sources and verification
Pitch and drill candidates were transcribed from the Tapmatic manufacturer chart; the M8 × 1.25 drill is from the Guhring SuperLine catalogue. Tapmatic’s chart assumes job drills cutting about 0.003 inch oversize. Manufacturer choices can differ.
NEEDS VERIFICATION: selected pitches against ISO 261 / ISO 262; recommended drills against ISO 2306 / DIN 336; minor-diameter limits against the specified thread tolerance standard and class. No minor-diameter limits are supplied.
06 / Questions
Frequently asked questions
What drill size should I use for M12 × 1.75?
Read it from the calculator on this page for the M12 × 1.75 selection, which shows a D − P cutting-tap estimate and a provisional chart drill (to be verified). The result is not a universal M12 value, and a different pitch or tap type needs its own selection.
Is M12 × 1.75 a coarse thread?
Yes. M12 × 1.75 is the ISO metric coarse thread for the M12 nominal size. A different pitch would be a different thread with its own core-hole requirement.
Is M12 × 1.75 normally machine tapped?
Machine tapping is common in production because the tap is large enough that torque and alignment are easier to control with a rigid setup. Hand tapping is still possible with a guided tap wrench and a firmly supported workpiece. The core hole is selected from the same calculator in either case.
How much clearance does a blind M12 × 1.75 hole need?
Enough depth below the required thread for the tap chamfer and for chips, with a separate specification for thread depth. A bottoming tap reduces the chamfer length but does not eliminate the need for clearance. Check the tap maker's guidance for the tap style.
Does stainless steel change the M12 × 1.75 tapping process?
It can. Some stainless grades work-harden, and the wrong lubrication or a dull tap can make the operation progressively harder. Confirm the tap and cutting data for the specific grade, and treat the calculator's chart drill as a starting point only, because it has no material setting.
Can I use a forming tap for M12 × 1.75?
A forming tap can work in ductile materials when the core hole is precise and lubrication is consistent. It avoids chips but requires a different hole from a cutting tap. Do not reuse a cutting-tap result; verify the forming-tap requirement with the manufacturer.
What if the M12 × 1.75 tap starts to bind?
Stop and investigate rather than forcing it. Binding can come from a tight core hole, packed chips, misalignment, a dull tap or insufficient lubrication. Remove the tap carefully, clear the hole and correct the cause before continuing.