The engineering workbench / fits and machine elements
M10 × 1.5 Tap Drill: Core Hole for Metric Coarse Thread
Estimate a cutting-tap drill as nominal thread diameter D minus pitch P. Compare that estimate with provisional manufacturer chart drills for selected metric coarse and fine threads.
Selected candidate ISO 261/262 metric pitch series only. Pitch assignments, chart drill sizes and all minor-diameter limits NEEDS VERIFICATION. Forming taps are outside this calculator.
8.5 mm D − P estimate · *chart drill 8.5 mm, provisional, to be verified
02 / Read the limits
Results
Dimensions and deviations in mm. Verification notes apply to the displayed source.
| Characteristic | Result · mm | Interpretation |
|---|---|---|
| Thread D × P | 10 × 1.5 mm | coarse; pitch series NEEDS VERIFICATION against ISO 261/262. |
| Cutting-tap estimate D − P | 8.5 mm | Approximation; excludes forming taps. |
| Provisional chart drill | 8.5 mm | NEEDS VERIFICATION against ISO 2306 / DIN 336; manufacturer-specific. |
| Minor-diameter limits | NEEDS VERIFICATION | Not supplied; no tolerance class or limits inferred from D − P. |
A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.
Selected coarse and fine pitch table — NEEDS VERIFICATION
| Thread | Series | Pitch · mm | D − P estimate · mm | Provisional chart drill · mm | Minor limits / status |
|---|---|---|---|---|---|
| M3 × 0.5 | coarse | 0.5 | 2.5 | 2.5 | Unavailable — NEEDS VERIFICATION |
| M4 × 0.7 | coarse | 0.7 | 3.3 | 3.3 | Unavailable — NEEDS VERIFICATION |
| M5 × 0.8 | coarse | 0.8 | 4.2 | 4.2 | Unavailable — NEEDS VERIFICATION |
| M6 × 1 | coarse | 1 | 5 | 5 | Unavailable — NEEDS VERIFICATION |
| M8 × 1.25 | coarse | 1.25 | 6.75 | 6.8 | Unavailable — NEEDS VERIFICATION |
| M10 × 1.25 | fine | 1.25 | 8.75 | 8.7 | Unavailable — NEEDS VERIFICATION |
| M10 × 1.5 | coarse | 1.5 | 8.5 | 8.5 | Unavailable — NEEDS VERIFICATION |
| M12 × 1.25 | fine | 1.25 | 10.75 | 10.8 | Unavailable — NEEDS VERIFICATION |
| M12 × 1.75 | coarse | 1.75 | 10.25 | 10.2 | Unavailable — NEEDS VERIFICATION |
| M16 × 1.5 | fine | 1.5 | 14.5 | 14.5 | Unavailable — NEEDS VERIFICATION |
| M16 × 2 | coarse | 2 | 14 | 14 | Unavailable — NEEDS VERIFICATION |
| M20 × 1.5 | fine | 1.5 | 18.5 | 18.5 | Unavailable — NEEDS VERIFICATION |
| M20 × 2.5 | coarse | 2.5 | 17.5 | 17.5 | Unavailable — NEEDS VERIFICATION |
| M24 × 2 | fine | 2 | 22 | 22 | Unavailable — NEEDS VERIFICATION |
| M24 × 3 | coarse | 3 | 21 | 21 | Unavailable — NEEDS VERIFICATION |
03 / How to use
How to use this calculator
- Confirm that the drawing specifies M10 × 1.5 and not another M10 pitch.
- Select the M10 × 1.5 — coarse preset in the calculator (it is preselected on this page), or enter D and P directly.
- The calculator has no tap-type or material input; it shows a D − P cutting-tap estimate and a provisional manufacturer chart drill (to be verified), and note whether tapping will be done by hand or machine.
- Read the drill size from the result and record the conditions used.
- For a blind hole, provide depth for the tap chamfer and chips, and check the required thread depth.
- Inspect the finished thread with the specified gauge and verify the hole position.
Table lookup, with explicit boundaries
Example: M8 × 1.25 → 8 − 1.25 = 6.75 mm (estimate).
The separate 6.8 mm manufacturer chart entry is provisional; it is not obtained by silently rounding every D − P result.
Minor-diameter limits are unavailable and are not derived from this formula.
Thread entries are selected discrete diameter/pitch pairs, not continuous standard ranges. Custom positive inputs with D > P are allowed for the formula only. A custom pair without chart data shows “Not tabulated”.
04 / Engineering context
M10 × 1.5 Tap Drill: Core Hole for a Metric Coarse Thread
M10 × 1.5 is a common ISO metric coarse thread for machine guards, brackets, mounts and general assemblies. At this size the tap is substantial, but the torque and the effect of a misaligned hole are also larger. Read the core-hole size from the calculator for M10 × 1.5 rather than scaling a result from a smaller thread.
Tapping torque rises with the amount of material being cut and with the length of thread being produced. A core hole that is too tight can overload a hand tap or stall a machine spindle; one that is too open can reduce engagement in a shallow or thin section. Coolant and chip evacuation matter in both through and blind holes, but blind holes leave less margin.
Power tapping can be efficient at this size, provided the spindle, tap holder and workpiece are aligned and the tap is suitable for the material. Hand tapping is still practical with a guided tap wrench and a properly supported part. Use the calculator result for M10 × 1.5 and confirm the tap maker's recommendations for cutting speed, lubrication and hole limits.
Thread data sources and verification
Pitch and drill candidates were transcribed from the Tapmatic manufacturer chart; the M8 × 1.25 drill is from the Guhring SuperLine catalogue. Tapmatic’s chart assumes job drills cutting about 0.003 inch oversize. Manufacturer choices can differ.
NEEDS VERIFICATION: selected pitches against ISO 261 / ISO 262; recommended drills against ISO 2306 / DIN 336; minor-diameter limits against the specified thread tolerance standard and class. No minor-diameter limits are supplied.
06 / Questions
Frequently asked questions
What drill size should I use for M10 × 1.5?
Use the calculator on this page with the M10 × 1.5 selection, which shows a D − P cutting-tap estimate and a provisional chart drill (to be verified). The result is specific to those inputs, so a value from another M10 pitch or another tap type is not a direct substitute.
Is M10 × 1.5 a coarse thread?
Yes. M10 × 1.5 is the ISO metric coarse thread for the M10 nominal size. A different pitch would be a different thread and would need its own core-hole selection.
Should I hand tap or machine tap M10 × 1.5?
Either can work. Hand tapping needs a guided, stable setup and a tap wrench that lets you control alignment. Machine tapping suits production and can give more consistent results when the spindle, holder and fixture are rigid. The better choice depends on the part, quantity and equipment.
How do I avoid chips in a blind M10 × 1.5 hole?
Use a tap style suited to blind holes, provide enough depth for the chamfer and chips, and clear the hole during the operation if possible. The core hole should not be enlarged just to create chip room, because that reduces thread engagement.
Does M10 × 1.5 need a different core hole in stainless steel?
The material can change how the tap performs, especially if the grade work-hardens. Follow the tap manufacturer's recommendation for the specific stainless grade and tap, and treat the calculator's chart drill as a starting point only, because it has no material setting. Lubrication and tool condition are part of the same decision.
Can I use a forming tap for M10 × 1.5?
A forming tap can be productive in ductile materials when the hole is precise and lubrication is reliable. It does not produce chips, but it requires a different core hole from a cutting tap. Do not reuse a cutting-tap result; confirm the forming-tap data with the tap maker.
What should I check after tapping M10 × 1.5?
Check the thread with the specified gauge, confirm the thread depth and inspect for tears or incomplete threads. Also check that the hole has not drifted during drilling, since position errors become more visible as the fastener size increases.