The engineering workbench / fits and machine elements
M3 × 0.5 Tap Drill: Core Hole for Metric Coarse Thread
Estimate a cutting-tap drill as nominal thread diameter D minus pitch P. Compare that estimate with provisional manufacturer chart drills for selected metric coarse and fine threads.
Selected candidate ISO 261/262 metric pitch series only. Pitch assignments, chart drill sizes and all minor-diameter limits NEEDS VERIFICATION. Forming taps are outside this calculator.
2.5 mm D − P estimate · *chart drill 2.5 mm, provisional, to be verified
02 / Read the limits
Results
Dimensions and deviations in mm. Verification notes apply to the displayed source.
| Characteristic | Result · mm | Interpretation |
|---|---|---|
| Thread D × P | 3 × 0.5 mm | coarse; pitch series NEEDS VERIFICATION against ISO 261/262. |
| Cutting-tap estimate D − P | 2.5 mm | Approximation; excludes forming taps. |
| Provisional chart drill | 2.5 mm | NEEDS VERIFICATION against ISO 2306 / DIN 336; manufacturer-specific. |
| Minor-diameter limits | NEEDS VERIFICATION | Not supplied; no tolerance class or limits inferred from D − P. |
A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.
Selected coarse and fine pitch table — NEEDS VERIFICATION
| Thread | Series | Pitch · mm | D − P estimate · mm | Provisional chart drill · mm | Minor limits / status |
|---|---|---|---|---|---|
| M3 × 0.5 | coarse | 0.5 | 2.5 | 2.5 | Unavailable — NEEDS VERIFICATION |
| M4 × 0.7 | coarse | 0.7 | 3.3 | 3.3 | Unavailable — NEEDS VERIFICATION |
| M5 × 0.8 | coarse | 0.8 | 4.2 | 4.2 | Unavailable — NEEDS VERIFICATION |
| M6 × 1 | coarse | 1 | 5 | 5 | Unavailable — NEEDS VERIFICATION |
| M8 × 1.25 | coarse | 1.25 | 6.75 | 6.8 | Unavailable — NEEDS VERIFICATION |
| M10 × 1.25 | fine | 1.25 | 8.75 | 8.7 | Unavailable — NEEDS VERIFICATION |
| M10 × 1.5 | coarse | 1.5 | 8.5 | 8.5 | Unavailable — NEEDS VERIFICATION |
| M12 × 1.25 | fine | 1.25 | 10.75 | 10.8 | Unavailable — NEEDS VERIFICATION |
| M12 × 1.75 | coarse | 1.75 | 10.25 | 10.2 | Unavailable — NEEDS VERIFICATION |
| M16 × 1.5 | fine | 1.5 | 14.5 | 14.5 | Unavailable — NEEDS VERIFICATION |
| M16 × 2 | coarse | 2 | 14 | 14 | Unavailable — NEEDS VERIFICATION |
| M20 × 1.5 | fine | 1.5 | 18.5 | 18.5 | Unavailable — NEEDS VERIFICATION |
| M20 × 2.5 | coarse | 2.5 | 17.5 | 17.5 | Unavailable — NEEDS VERIFICATION |
| M24 × 2 | fine | 2 | 22 | 22 | Unavailable — NEEDS VERIFICATION |
| M24 × 3 | coarse | 3 | 21 | 21 | Unavailable — NEEDS VERIFICATION |
03 / How to use
How to use this calculator
- Confirm that the drawing says M3 × 0.5 and not a different M3 pitch.
- Select the M3 × 0.5 — coarse preset in the calculator (it is preselected on this page), or enter D and P directly.
- The calculator has no tap-type or material input; it shows a D − P cutting-tap estimate and a provisional manufacturer chart drill (to be verified), then read the result with its stated assumptions in mind.
- Read the drill size from the result. Do not substitute a size from another thread or material.
- For a blind hole, add drill depth for the tap chamfer and chips, and specify thread depth separately.
- Check the finished thread with the specified gauge or a known-good mating fastener.
Table lookup, with explicit boundaries
Example: M8 × 1.25 → 8 − 1.25 = 6.75 mm (estimate).
The separate 6.8 mm manufacturer chart entry is provisional; it is not obtained by silently rounding every D − P result.
Minor-diameter limits are unavailable and are not derived from this formula.
Thread entries are selected discrete diameter/pitch pairs, not continuous standard ranges. Custom positive inputs with D > P are allowed for the formula only. A custom pair without chart data shows “Not tabulated”.
04 / Engineering context
M3 × 0.5 Tap Drill: Core Hole for a Small Metric Coarse Thread
M3 × 0.5 is the ISO metric coarse thread for a small fastener. At this scale the tap has a slender cross-section, so hole quality, alignment and lubrication can matter as much as the nominal callout. Read the core-hole size from the calculator on this page for the exact M3 × 0.5 selection; do not copy a diameter from an M3 fine thread, another material or an old shop chart.
The core hole sets how much material the tap has to remove or displace. With M3 × 0.5, a hole near the tight end of the usable range can raise torque and breakage risk in a tap that has little material to spare. A hole near the open end eases tapping but leaves less thread engagement in thin bosses and small enclosures. In practice, the available boss depth and the required pull-out strength often decide the design before the drill is chosen.
Cutting taps and forming taps place different demands on the hole. Forming taps need a precise diameter and good lubrication, while cutting taps need room for chips, especially in blind holes. ISO 68-1 defines the thread profile, ISO 262 selects common fastener sizes, and ISO 724 gives basic dimensions; they do not replace the tap manufacturer's core-hole guidance. Use the calculator result as the starting point for the M3 × 0.5 job and verify it against the tap data and the drawing.
Thread data sources and verification
Pitch and drill candidates were transcribed from the Tapmatic manufacturer chart; the M8 × 1.25 drill is from the Guhring SuperLine catalogue. Tapmatic’s chart assumes job drills cutting about 0.003 inch oversize. Manufacturer choices can differ.
NEEDS VERIFICATION: selected pitches against ISO 261 / ISO 262; recommended drills against ISO 2306 / DIN 336; minor-diameter limits against the specified thread tolerance standard and class. No minor-diameter limits are supplied.
06 / Questions
Frequently asked questions
What drill size should I use for M3 × 0.5?
Use the calculator on this page with the M3 × 0.5 selection, which shows a D − P cutting-tap estimate and a provisional chart drill (to be verified). There is no single diameter that is correct for every cutting tap, forming tap, material and engagement target, so the result must come from the chosen conditions.
Is M3 × 0.5 a coarse thread?
Yes. M3 × 0.5 is the ISO metric coarse thread for the M3 nominal size. A fine M3 thread has a different pitch and therefore a different core-hole requirement, so the complete callout must be checked before drilling.
Why is M3 × 0.5 tapping sensitive to the core hole?
The tap is small and has limited torque capacity. A tight hole, a blunt tap or poor alignment can raise torque quickly, and a broken tap is difficult to remove from a small part. Chips also have little room to escape in a blind hole, so the hole size and depth plan need to work with the tap style.
Can I use a forming tap for M3 × 0.5?
A forming tap can be used in suitable ductile materials, but it needs a precise core hole and good lubrication. Its hole requirement is not the same as a cutting tap's. Do not reuse a cutting-tap result; confirm the forming-tap hole with the tap maker.
How deep should the hole be for a blind M3 × 0.5 thread?
The hole must be deeper than the required thread so the tap chamfer can enter and chips can collect without packing at the bottom. A spiral-flute or bottoming tap may help, but it does not remove the need for depth clearance. Specify thread depth and drill depth as separate requirements.
Should I use the same drill for aluminum and stainless steel with M3 × 0.5?
Not necessarily. Aluminum can gall, and some stainless steels work-harden, so the same core hole and tap may not behave the same way in both materials. Follow the tap manufacturer's recommendation and adjust lubrication and tap style before changing the core hole.
Can I enlarge the hole slightly to reduce breakage risk?
Only within the range allowed for the tap and the joint. A larger hole may reduce torque, but it also reduces thread engagement, which matters in small bosses and thin sections. Do not trade away engagement without checking the design requirement.