EngineeringFits中文 / Chinese version ↗

The engineering workbench / fits and machine elements

ISO 286 h7 Shaft Tolerance Class: Limits and Fits

Look up h7 shaft upper and lower deviations in micrometres, plus minimum and maximum sizes in millimetres. Values reuse the existing English ISO 286 dataset.

Table intervals cover nominal sizes greater than 0 and up to 500 mm. The existing English calculator supports 1–500 mm; results below 1 mm require verification.

02 / Read the limits

Results

Deviations in µm; nominal and limit sizes in mm.

CharacteristicResult · µm / mmInterpretation
Nominal size25 mmEnglish ISO 286 dataset.
Upper deviation0 µmHole ES / shaft es.
Lower deviation-21 µmHole EI / shaft ei.
Minimum size24.979 mmNominal + lower deviation / 1000.
Maximum size25 mmNominal + upper deviation / 1000.

A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.

h7 shaft size-range table

Nominal size > lower to ≤ upper · mmUpper deviation · µmLower deviation · µmVerification note
>0 to ≤30-10Below 1 mm NEEDS VERIFICATION
>3 to ≤60-12English dataset
>6 to ≤100-15English dataset
>10 to ≤180-18English dataset
>18 to ≤300-21English dataset
>30 to ≤500-25English dataset
>50 to ≤800-30English dataset
>80 to ≤1200-35English dataset
>120 to ≤1800-40English dataset
>180 to ≤2500-46English dataset
>250 to ≤3150-52English dataset
>315 to ≤4000-57English dataset
>400 to ≤5000-63English dataset

03 / How to use

How to use this calculator

  1. This page looks up the ISO 286 h7 shaft class. Enter the nominal size of the shaft in the field below; the class is already fixed for this page.
  2. Read the upper and lower limit deviations and the resulting limits. For an h shaft, check that the upper limit sits at the nominal size.
  3. The size-range table on this page lists the same deviations for every tabulated band.
  4. To evaluate a fit with a mating hole such as H7, open the ISO 286 fit calculator and select both classes there. This page shows the h7 shaft limits only.
  5. Use the result for that nominal size only; the tabulated values change between size bands.

Table lookup, with explicit boundaries

Read the tabulated upper and lower deviations.
Minimum size = nominal + lower deviation / 1000.
Maximum size = nominal + upper deviation / 1000.
Deviations: µm; sizes: mm.

The first interval includes its lower tabulated size. Each following interval excludes its lower endpoint and includes its upper endpoint. The calculator rejects inputs outside the stated range and does not round inputs across a boundary.

04 / Engineering context

ISO 286 h7 Shaft Tolerance: Limits and Fits

An h7 shaft is a shaft tolerance class in ISO 286. The lowercase h is the fundamental deviation: the upper limit of the shaft coincides with the nominal size, so every permitted size lies at or below it. The 7 is the IT7 grade and sets the width of the tolerance zone. In a drawing or a fit callout, h7 is one class; the letter and the number are not chosen independently.

Because an h shaft does not exceed the nominal size, it is a natural partner for an H hole in a clearance location. H7/h6 is a familiar close clearance pairing, while H7/h7 puts both nominal-size limits together and gives line-to-line contact at the minimum. The h7 class can also be used on non-circular features and as the shaft of a shaft-basis fit, where the h shaft is the reference and the hole letter is varied. It controls size only; roundness, straightness and surface texture need their own requirements when they matter.

h7 is a middle-precision shaft class. It is used where a shaft must locate or slide without being larger than the nominal size, and where the IT7 band is acceptable. It is not a fit by itself: the mating hole decides whether the assembly has clearance, transition or interference. A hole whose limits sit below the shaft limits could produce interference even with an h7 shaft, while an H7 hole produces clearance. Read the pair, not the shaft class alone.

ISO 286 data source

Numerical source: existing ISO 286 JSON, with the h/H, js, f/g and k/p rules in the existing engine. Dataset edition label: ISO 286-1:2010 / ISO 286-2:2010. This lookup adds no new fundamental-deviation formula.

06 / Questions

Frequently asked questions

What does h7 mean?

The h is the fundamental-deviation letter for a shaft whose upper limit is at the nominal size. The 7 is the IT7 standard tolerance grade and determines the width of the shaft zone. Together they define the h7 shaft class.

Where is the upper limit of an h7 shaft?

It coincides with the nominal size. The lower limit is below it by the IT7 tolerance for that nominal size, so a conforming h7 shaft is never larger than the nominal size.

Is h7 a clearance fit?

Not by itself. A shaft class only describes the shaft. H7/h7 is a clearance pairing because the H7 hole starts at the nominal size, but h7 matched with a smaller hole could produce a transition or interference condition. Always read the hole and shaft together.

What is the difference between H7/h6 and H7/h7?

Both are hole-basis clearance pairs, but they use different shaft grades. H7/h6 uses the tighter h6 shaft and is a familiar close clearance fit. H7/h7 uses the h7 shaft covered here; its minimum clearance is line-to-line because the H7 lower limit and the h7 upper limit both sit at the nominal size.

How does h7 differ from h6?

Both are h shafts, so both have their upper limit at the nominal size. h6 uses the narrower IT6 grade; h7 uses the wider IT7 grade. h6 therefore gives a smaller shaft tolerance and generally a tighter assembly, while h7 allows more manufacturing variation.

Is h7 a shaft-basis tolerance?

The letter h is the reference shaft used in the shaft-basis system, but h7 is simply a tolerance class. A fit is shaft-basis only when the design fixes the shaft as h and varies the hole class. An h7 shaft can appear in either hole-basis or shaft-basis arrangements.

Does h7 control surface finish or straightness?

No. h7 limits the size of the feature. Surface texture, straightness, roundness and cylindricity are separate characteristics and must be specified separately if the application depends on them.

Why do the deviations change with size?

The limit deviations for h7 depend on the nominal size and come from the ISO 286-2 tables. This page lists those values in the size-range table, and the calculator applies the class to the size you enter so the result matches the correct size band.