The engineering workbench / fits and machine elements
ISO 286 f7 Shaft Tolerance: Clearance Fit with H8
Look up f7 shaft upper and lower deviations in micrometres, plus minimum and maximum sizes in millimetres. Values reuse the existing English ISO 286 dataset.
Table intervals cover nominal sizes greater than 0 and up to 500 mm. The existing English calculator supports 1–500 mm; results below 1 mm require verification.
02 / Read the limits
Results
Deviations in µm; nominal and limit sizes in mm.
| Characteristic | Result · µm / mm | Interpretation |
|---|---|---|
| Nominal size | 25 mm | English ISO 286 dataset. |
| Upper deviation | -20 µm | Hole ES / shaft es. |
| Lower deviation | -41 µm | Hole EI / shaft ei. |
| Minimum size | 24.959 mm | Nominal + lower deviation / 1000. |
| Maximum size | 24.98 mm | Nominal + upper deviation / 1000. |
A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.
f7 shaft size-range table
| Nominal size > lower to ≤ upper · mm | Upper deviation · µm | Lower deviation · µm | Verification note |
|---|---|---|---|
| >0 to ≤3 | -6 | -16 | Below 1 mm NEEDS VERIFICATION |
| >3 to ≤6 | -10 | -22 | English dataset |
| >6 to ≤10 | -13 | -28 | English dataset |
| >10 to ≤14 | -16 | -34 | English dataset |
| >14 to ≤18 | -16 | -34 | English dataset |
| >18 to ≤24 | -20 | -41 | English dataset |
| >24 to ≤30 | -20 | -41 | English dataset |
| >30 to ≤40 | -25 | -50 | English dataset |
| >40 to ≤50 | -25 | -50 | English dataset |
| >50 to ≤65 | -30 | -60 | English dataset |
| >65 to ≤80 | -30 | -60 | English dataset |
| >80 to ≤100 | -36 | -71 | English dataset |
| >100 to ≤120 | -36 | -71 | English dataset |
| >120 to ≤140 | -43 | -83 | English dataset |
| >140 to ≤160 | -43 | -83 | English dataset |
| >160 to ≤180 | -43 | -83 | English dataset |
| >180 to ≤200 | -50 | -96 | English dataset |
| >200 to ≤225 | -50 | -96 | English dataset |
| >225 to ≤250 | -50 | -96 | English dataset |
| >250 to ≤280 | -56 | -108 | English dataset |
| >280 to ≤315 | -56 | -108 | English dataset |
| >315 to ≤355 | -62 | -119 | English dataset |
| >355 to ≤400 | -62 | -119 | English dataset |
| >400 to ≤450 | -68 | -131 | English dataset |
| >450 to ≤500 | -68 | -131 | English dataset |
03 / How to use
How to use this calculator
- This page looks up the ISO 286 f7 shaft class. Enter the nominal size of the shaft in the field below; the class is already fixed for this page.
- Read the upper and lower limit deviations and the resulting limits. An f7 shaft should lie below the nominal size at both limits.
- The size-range table on this page lists the same deviations for every tabulated band.
- To evaluate the common pairing with an H8 hole, open the ISO 286 fit calculator and select H8 and f7 there. This page shows the f7 shaft limits only.
- Use the result for the entered nominal size only; the deviations and IT7 width are tabulated by size band.
Table lookup, with explicit boundaries
Minimum size = nominal + lower deviation / 1000.
Maximum size = nominal + upper deviation / 1000.
Deviations: µm; sizes: mm.
The first interval includes its lower tabulated size. Each following interval excludes its lower endpoint and includes its upper endpoint. The calculator rejects inputs outside the stated range and does not round inputs across a boundary.
04 / Engineering context
ISO 286 f7 Shaft Tolerance Class: Clearance Fit with H8
An f7 shaft is a shaft tolerance class in ISO 286. The lowercase f is a fundamental deviation below the nominal size, and the interval sits farther below the nominal size than a g shaft. The 7 is the IT7 grade. The result is a shaft with a deliberate clearance allowance, used where a part must run or slide with more freedom than a close g6 fit allows.
H8/f7 is a common running fit. The H8 hole begins at the nominal size, and the f7 shaft remains below it, so the pair has clearance at every combination of limits. It is used for sliding shafts, plain-bearing journals and other running applications where a lubricant film or easy assembly is more important than minimal play. The wider H8 hole and the lower f7 shaft generally give more clearance than an H7/g6 pair; that is a comparison of the classes, not a numeric value for a particular size.
f7 controls size only. A running fit also depends on surface finish, roundness, alignment, lubrication, speed, temperature and the materials. Those are not set by the f7 callout. In addition, H8/f7 is a clearance fit by design, but the actual minimum and maximum clearance still come from the nominal size and the tabulated limits; use the calculator rather than a rule of thumb.
ISO 286 data source
Numerical source: existing ISO 286 JSON, with the h/H, js, f/g and k/p rules in the existing engine. Dataset edition label: ISO 286-1:2010 / ISO 286-2:2010. This lookup adds no new fundamental-deviation formula.
06 / Questions
Frequently asked questions
What does f7 mean?
The f is a shaft fundamental deviation below the nominal size, and the 7 is the IT7 tolerance grade. Together they define a shaft class with a clearance allowance and a relatively fine tolerance band.
What is H8/f7 used for?
H8/f7 is a common clearance or running fit. It is used where a shaft must rotate or slide with more freedom than a close fit provides, and where some variation in clearance can be tolerated. Plain-bearing journals and sliding shafts are typical examples.
Is H8/f7 always a clearance fit?
Yes. The H8 hole starts at the nominal size and the f7 shaft remains below it, so the hole limits are never smaller than the shaft limits. The actual minimum and maximum clearance still depend on the nominal size and must be read from the calculation.
How does f7 differ from g6?
Both are clearance shaft classes, but f7 sits farther below the nominal size than g6. An H8/f7 pair therefore generally has more clearance than an H7/g6 pair, and it is used where easier running or assembly is more important than minimal play.
Is f7 a shaft-basis tolerance?
f7 is a shaft tolerance class, not a fit system. H8/f7 is a hole-basis fit because the hole is H8. A shaft-basis fit would use an h shaft and vary the hole class. The same f7 shaft could be paired with another hole, with a different result.
Can f7 be used for every bearing application?
No. Bearing type, load direction, speed, lubrication, temperature and housing design all affect the required fit. Bearing manufacturers publish recommended shaft and housing tolerances for their products; follow those recommendations rather than treating f7 as a universal bearing fit.
Does f7 control surface finish or roundness?
No. f7 limits the size of the shaft. Surface texture, roundness, cylindricity and alignment are separate requirements and must be specified when they affect running performance.
Why does the calculator ask for the nominal size?
The f fundamental deviation and the IT7 tolerance width are tabulated by nominal-size band. Entering the size lets the calculator select the correct band and return the applicable limits and fit range.