The engineering workbench / fits and machine elements
ISO 286 p6 Shaft Tolerance: Interference Fit with H7
Look up p6 shaft upper and lower deviations in micrometres, plus minimum and maximum sizes in millimetres. Values reuse the existing English ISO 286 dataset.
Table intervals cover nominal sizes greater than 0 and up to 500 mm. The existing English calculator supports 1–500 mm; results below 1 mm require verification.
02 / Read the limits
Results
Deviations in µm; nominal and limit sizes in mm.
| Characteristic | Result · µm / mm | Interpretation |
|---|---|---|
| Nominal size | 25 mm | English ISO 286 dataset. |
| Upper deviation | +35 µm | Hole ES / shaft es. |
| Lower deviation | +22 µm | Hole EI / shaft ei. |
| Minimum size | 25.022 mm | Nominal + lower deviation / 1000. |
| Maximum size | 25.035 mm | Nominal + upper deviation / 1000. |
A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.
p6 shaft size-range table
| Nominal size > lower to ≤ upper · mm | Upper deviation · µm | Lower deviation · µm | Verification note |
|---|---|---|---|
| >0 to ≤3 | +12 | +6 | Below 1 mm NEEDS VERIFICATION |
| >3 to ≤6 | +20 | +12 | English dataset |
| >6 to ≤10 | +24 | +15 | English dataset |
| >10 to ≤14 | +29 | +18 | English dataset |
| >14 to ≤18 | +29 | +18 | English dataset |
| >18 to ≤24 | +35 | +22 | English dataset |
| >24 to ≤30 | +35 | +22 | English dataset |
| >30 to ≤40 | +42 | +26 | English dataset |
| >40 to ≤50 | +42 | +26 | English dataset |
| >50 to ≤65 | +51 | +32 | English dataset |
| >65 to ≤80 | +51 | +32 | English dataset |
| >80 to ≤100 | +59 | +37 | English dataset |
| >100 to ≤120 | +59 | +37 | English dataset |
| >120 to ≤140 | +68 | +43 | English dataset |
| >140 to ≤160 | +68 | +43 | English dataset |
| >160 to ≤180 | +68 | +43 | English dataset |
| >180 to ≤200 | +79 | +50 | English dataset |
| >200 to ≤225 | +79 | +50 | English dataset |
| >225 to ≤250 | +79 | +50 | English dataset |
| >250 to ≤280 | +88 | +56 | English dataset |
| >280 to ≤315 | +88 | +56 | English dataset |
| >315 to ≤355 | +98 | +62 | English dataset |
| >355 to ≤400 | +98 | +62 | English dataset |
| >400 to ≤450 | +108 | +68 | English dataset |
| >450 to ≤500 | +108 | +68 | English dataset |
03 / How to use
How to use this calculator
- This page looks up the ISO 286 p6 shaft class. Enter the nominal size of the shaft in the field below; the class is already fixed for this page.
- Read the upper and lower limit deviations and the resulting limits. A p6 shaft should lie above the nominal size at both limits.
- The size-range table on this page lists the same deviations for every tabulated band.
- To evaluate the common pairing with an H7 hole, open the ISO 286 fit calculator and select H7 and p6 there. This page shows the p6 shaft limits only.
- Confirm whether the result is full interference or a transition condition before choosing an assembly method.
Table lookup, with explicit boundaries
Minimum size = nominal + lower deviation / 1000.
Maximum size = nominal + upper deviation / 1000.
Deviations: µm; sizes: mm.
The first interval includes its lower tabulated size. Each following interval excludes its lower endpoint and includes its upper endpoint. The calculator rejects inputs outside the stated range and does not round inputs across a boundary.
04 / Engineering context
ISO 286 p6 Shaft Tolerance Class: Interference Fit with H7
A p6 shaft is a shaft tolerance class in ISO 286. The lowercase p places the shaft interval above the nominal size, so a p6 shaft is intended to be larger than the nominal size. The 6 is the IT6 grade, which keeps the band relatively narrow. The combination H7/p6 is widely used as a light interference or press fit, but the actual interference depends on the nominal size and on where the two parts fall within their limits.
In an H7/p6 assembly, the hole is at or above the nominal size and the shaft is above it, so the fit is biased toward interference. It is used for parts that must stay together without a separate clamp, such as bushings, dowel pins and small hubs, and it can often be assembled with a press. The fit is not a substitute for a torque calculation: the amount of interference, the materials, the contact length and friction all affect how much load the joint can carry.
p6 is a size class, not a press-fit design procedure. ISO 286 gives the limits; it does not give the assembly force, contact pressure, hoop stress or temperature needed for a safe joint. Those require a separate interference-fit calculation and a check of the materials. At some small nominal sizes the H7/p6 pair may be a transition rather than a full interference fit, so never assume the family from the letter alone.
ISO 286 data source
Numerical source: existing ISO 286 JSON, with the h/H, js, f/g and k/p rules in the existing engine. Dataset edition label: ISO 286-1:2010 / ISO 286-2:2010. This lookup adds no new fundamental-deviation formula.
06 / Questions
Frequently asked questions
What does p6 mean?
The p is a shaft fundamental deviation above the nominal size, and the 6 is the IT6 tolerance grade. Together they define a shaft class whose tolerance zone sits above the nominal size.
What does H7/p6 mean?
H7/p6 is a hole-basis fit with an H7 hole and a p6 shaft. It is commonly used as a light interference or press fit, where the shaft is larger than the hole and the parts are held together by friction after assembly.
Is H7/p6 always an interference fit?
It is commonly an interference fit, but it should not be assumed for every nominal size. At small nominal sizes the calculated limits can produce a transition condition rather than interference throughout the range. Check the result for the size in hand.
How is an H7/p6 joint assembled?
Depending on the amount of interference and the materials, the joint may be pressed, or one part may be heated or cooled to change its size temporarily. The assembly method should be chosen from the calculated interference and a check of contact pressure and material stress, not from the class name alone.
How does p6 differ from k6?
Both place the shaft zone at or above the nominal size, but p6 is offset farther in the positive direction. H7/p6 is therefore biased toward interference, while H7/k6 is a transition fit that can produce a small clearance or a small interference.
Does p6 guarantee torque capacity?
No. Interference can produce friction, but the torque capacity depends on the actual interference, materials, surface finish, contact length and coefficient of friction. Use a separate joint calculation and add a positive drive where the load demands it.
Can p6 be paired with a hole other than H7?
Yes, but the fit changes. A different hole class or grade shifts the hole limits and can turn the pair into a transition or clearance fit. Always evaluate the actual hole and shaft classes at the same nominal size.
Does p6 control surface finish or roundness?
No. p6 controls the size of the shaft. Surface texture, roundness, cylindricity and alignment affect the press fit and need separate specifications when they are functionally important.