The engineering workbench / fits and machine elements
ISO 286 g6 Shaft Tolerance Class: Close Running Fit
Look up g6 shaft upper and lower deviations in micrometres, plus minimum and maximum sizes in millimetres. Values reuse the existing English ISO 286 dataset.
Table intervals cover nominal sizes greater than 0 and up to 500 mm. The existing English calculator supports 1–500 mm; results below 1 mm require verification.
02 / Read the limits
Results
Deviations in µm; nominal and limit sizes in mm.
| Characteristic | Result · µm / mm | Interpretation |
|---|---|---|
| Nominal size | 25 mm | English ISO 286 dataset. |
| Upper deviation | -7 µm | Hole ES / shaft es. |
| Lower deviation | -20 µm | Hole EI / shaft ei. |
| Minimum size | 24.98 mm | Nominal + lower deviation / 1000. |
| Maximum size | 24.993 mm | Nominal + upper deviation / 1000. |
A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.
g6 shaft size-range table
| Nominal size > lower to ≤ upper · mm | Upper deviation · µm | Lower deviation · µm | Verification note |
|---|---|---|---|
| >0 to ≤3 | -2 | -8 | Below 1 mm NEEDS VERIFICATION |
| >3 to ≤6 | -4 | -12 | English dataset |
| >6 to ≤10 | -5 | -14 | English dataset |
| >10 to ≤14 | -6 | -17 | English dataset |
| >14 to ≤18 | -6 | -17 | English dataset |
| >18 to ≤24 | -7 | -20 | English dataset |
| >24 to ≤30 | -7 | -20 | English dataset |
| >30 to ≤40 | -9 | -25 | English dataset |
| >40 to ≤50 | -9 | -25 | English dataset |
| >50 to ≤65 | -10 | -29 | English dataset |
| >65 to ≤80 | -10 | -29 | English dataset |
| >80 to ≤100 | -12 | -34 | English dataset |
| >100 to ≤120 | -12 | -34 | English dataset |
| >120 to ≤140 | -14 | -39 | English dataset |
| >140 to ≤160 | -14 | -39 | English dataset |
| >160 to ≤180 | -14 | -39 | English dataset |
| >180 to ≤200 | -15 | -44 | English dataset |
| >200 to ≤225 | -15 | -44 | English dataset |
| >225 to ≤250 | -15 | -44 | English dataset |
| >250 to ≤280 | -17 | -49 | English dataset |
| >280 to ≤315 | -17 | -49 | English dataset |
| >315 to ≤355 | -18 | -54 | English dataset |
| >355 to ≤400 | -18 | -54 | English dataset |
| >400 to ≤450 | -20 | -60 | English dataset |
| >450 to ≤500 | -20 | -60 | English dataset |
03 / How to use
How to use this calculator
- This page looks up the ISO 286 g6 shaft class. Enter the nominal size of the shaft in the field below; the class is already fixed for this page.
- Read the upper and lower limit deviations and the resulting limits. A g6 shaft should lie below the nominal size at both limits.
- The size-range table on this page lists the same deviations for every tabulated band.
- To evaluate the common pairing with an H7 hole, open the ISO 286 fit calculator and select H7 and g6 there. This page shows the g6 shaft limits only.
- Use the result for the entered nominal size only, because both the fundamental deviation and the IT6 width change with size.
Table lookup, with explicit boundaries
Minimum size = nominal + lower deviation / 1000.
Maximum size = nominal + upper deviation / 1000.
Deviations: µm; sizes: mm.
The first interval includes its lower tabulated size. Each following interval excludes its lower endpoint and includes its upper endpoint. The calculator rejects inputs outside the stated range and does not round inputs across a boundary.
04 / Engineering context
ISO 286 g6 Shaft Tolerance Class: Close Running Fit
A g6 shaft is a shaft tolerance class in ISO 286. The lowercase g is a fundamental deviation below the nominal size, so the whole shaft interval sits on the low side of the nominal size. The 6 is the IT6 grade and sets the width of that interval. The result is a shaft that is deliberately made a little smaller than the nominal size but held to a relatively fine band; the exact limits depend on the nominal size and must come from the table or the calculator.
g6 is most often seen in H7/g6, a close running or sliding fit. Because the H7 hole starts at the nominal size and the g6 shaft stays below it, the pair has clearance throughout its limits; the amount is small enough to guide a part without the looseness of a coarse fit. It is used for sliding sleeves, locating pins, lightly loaded shafts and similar parts that must move or assemble freely without excessive play. It is not a universal running-bearing fit: speed, lubrication, temperature and bearing type can demand a different class.
The g6 class controls size only. A shaft can be within its g6 limits and still have unacceptable roundness, taper or surface finish, and those characteristics affect a running fit as much as the size band does. Specify them separately when the application needs them. Also remember that g6 is a shaft class, not a fit: pairing it with a hole other than H7 changes the clearance and may change the fit family.
ISO 286 data source
Numerical source: existing ISO 286 JSON, with the h/H, js, f/g and k/p rules in the existing engine. Dataset edition label: ISO 286-1:2010 / ISO 286-2:2010. This lookup adds no new fundamental-deviation formula.
06 / Questions
Frequently asked questions
What does g6 mean?
The g is a shaft fundamental deviation below the nominal size, and the 6 is the IT6 tolerance grade. Together they define a shaft class whose tolerance zone sits just below the nominal size.
Why is g6 often paired with H7?
The combination gives a close running or sliding fit. The H7 hole lies at and above the nominal size, while the g6 shaft lies below it, so the pair has clearance at all combinations of limits. The clearance is small enough to control play while still allowing movement.
Is H7/g6 always a clearance fit?
Yes. The hole zone starts at the nominal size and the shaft zone remains below it, so the hole limits are never smaller than the shaft limits. The actual minimum and maximum clearance still depend on the nominal size and must be read from the calculated result.
How does g6 differ from h6?
Both are shafts below or at the nominal size, but their zones are placed differently. h6 has its upper limit at the nominal size and can meet an H7 hole line-to-line. g6 sits entirely below the nominal size, so an H7/g6 pair has positive clearance rather than a line-to-line minimum.
Is g6 a precision tolerance class?
IT6 is a relatively fine grade, but g6 is not the tightest class available and precision depends on the whole design. The hole grade, nominal size, form tolerances, surface finish and measurement method all affect whether the assembly behaves as intended.
Does g6 control surface finish or roundness?
No. g6 limits the size of the shaft. Roundness, cylindricity, straightness and surface texture are separate requirements and need their own specifications when they are functionally important.
What is a close running fit?
It is a clearance fit intended for parts that move relative to one another with little play. The fit must still leave enough clearance for assembly, lubrication and thermal movement, so the application data matter as much as the class label.
Why does the calculator need the nominal size?
The g fundamental deviation and the IT6 tolerance width are both tabulated by nominal-size band. A different nominal size can produce a different deviation and a different zone width, so the calculator must apply the class to the size in hand.