The engineering workbench / fits and machine elements
ISO 286 js6 Shaft Tolerance Class: Symmetrical Zone
Look up js6 shaft upper and lower deviations in micrometres, plus minimum and maximum sizes in millimetres. Values reuse the existing English ISO 286 dataset.
Table intervals cover nominal sizes greater than 0 and up to 500 mm. The existing English calculator supports 1–500 mm; results below 1 mm require verification.
02 / Read the limits
Results
Deviations in µm; nominal and limit sizes in mm.
| Characteristic | Result · µm / mm | Interpretation |
|---|---|---|
| Nominal size | 25 mm | English ISO 286 dataset. |
| Upper deviation | +6.5 µm | Hole ES / shaft es. |
| Lower deviation | -6.5 µm | Hole EI / shaft ei. |
| Minimum size | 24.9935 mm | Nominal + lower deviation / 1000. |
| Maximum size | 25.0065 mm | Nominal + upper deviation / 1000. |
A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.
js6 shaft size-range table
| Nominal size > lower to ≤ upper · mm | Upper deviation · µm | Lower deviation · µm | Verification note |
|---|---|---|---|
| >0 to ≤3 | +3 | -3 | Below 1 mm NEEDS VERIFICATION |
| >3 to ≤6 | +4 | -4 | English dataset |
| >6 to ≤10 | +4.5 | -4.5 | English dataset |
| >10 to ≤18 | +5.5 | -5.5 | English dataset |
| >18 to ≤30 | +6.5 | -6.5 | English dataset |
| >30 to ≤50 | +8 | -8 | English dataset |
| >50 to ≤80 | +9.5 | -9.5 | English dataset |
| >80 to ≤120 | +11 | -11 | English dataset |
| >120 to ≤180 | +12.5 | -12.5 | English dataset |
| >180 to ≤250 | +14.5 | -14.5 | English dataset |
| >250 to ≤315 | +16 | -16 | English dataset |
| >315 to ≤400 | +18 | -18 | English dataset |
| >400 to ≤500 | +20 | -20 | English dataset |
03 / How to use
How to use this calculator
- This page looks up the ISO 286 js6 shaft class. Enter the nominal size of the shaft in the field below; the class is already fixed for this page.
- Read the upper and lower limit deviations and the resulting limits. For js6, check that the zone is disposed on both sides of the nominal size.
- The size-range table on this page lists the same deviations for every tabulated band.
- To evaluate a fit with a mating hole such as H7, open the ISO 286 fit calculator and select both classes there. This page shows the js6 shaft limits only.
- Use the result for that nominal size; the deviations are tabulated by size band.
Table lookup, with explicit boundaries
Minimum size = nominal + lower deviation / 1000.
Maximum size = nominal + upper deviation / 1000.
Deviations: µm; sizes: mm.
The first interval includes its lower tabulated size. Each following interval excludes its lower endpoint and includes its upper endpoint. The calculator rejects inputs outside the stated range and does not round inputs across a boundary.
04 / Engineering context
ISO 286 js6 Shaft Tolerance Class: A Symmetrical Zone
A js6 shaft is a shaft tolerance class in ISO 286 whose tolerance interval is arranged symmetrically about the nominal size. The lowercase js is the special case among shaft tolerance-zone letters: instead of sitting wholly above or below the nominal size, the interval straddles it, with one deviation on each side. The 6 is the IT6 grade, so the total width of the zone is the IT6 value for the nominal size.
Because js6 is centered on the nominal size, it does not carry a built-in offset toward clearance or interference. H7/js6 is commonly a transition fit: the H7 hole lies at and above the nominal size, while the js6 shaft crosses it, so the assembly may end up with a small clearance or a small interference depending on the actual sizes. That makes js6 useful for locating features that must assemble without a deliberate loose or press bias, and for parts that may need occasional disassembly. It is less suitable when the design depends on a guaranteed clearance or a guaranteed grip.
The symmetric placement is a property of the js letter, not a claim that the fit is symmetrical. The hole class still shifts the result. A js6 shaft paired with a hole other than H7 may be clearance, transition or interference. As with every ISO 286 class, js6 controls size only; form, orientation and surface texture need separate control.
ISO 286 data source
Numerical source: existing ISO 286 JSON, with the h/H, js, f/g and k/p rules in the existing engine. Dataset edition label: ISO 286-1:2010 / ISO 286-2:2010. This lookup adds no new fundamental-deviation formula.
06 / Questions
Frequently asked questions
What does js6 mean?
The js is a shaft tolerance-zone letter whose interval is arranged symmetrically about the nominal size. The 6 is the IT6 tolerance grade and sets the zone width. Together they define the js6 shaft class.
Why is js6 symmetrical?
The js letter is defined so that the two limit deviations lie on opposite sides of the nominal size rather than wholly above or below it. This centered position is what distinguishes js from one-sided shaft letters such as g, h, k or p.
What fit does H7/js6 give?
H7/js6 is commonly a transition fit. The hole zone starts at the nominal size, while the shaft zone crosses it, so some assemblies have a small clearance and others have a small interference. The actual result depends on the nominal size and on where the two parts fall within their limits.
Is js6 always exactly symmetrical?
The class is defined by a symmetrical placement about the nominal size. The published limit deviations for a specific nominal size are the authority for inspection and calculation, and the calculator returns those values rather than a rounded rule of thumb.
How does js6 differ from k6?
Both can form transition fits with an H7 hole, but their zones are placed differently. js6 is centered on the nominal size, with deviations on both sides. k6 sits at or just above the nominal size, so it is biased more toward interference than js6 is.
Is js6 a clearance fit?
No. A shaft class is not a fit. js6 can be part of a clearance, transition or interference pairing depending on the hole class and the actual limits. With H7 it is normally treated as a transition fit.
Does js6 control surface finish or geometry?
No. js6 limits the size of the shaft. Roundness, cylindricity, straightness, orientation and surface texture are separate requirements and need their own specifications.
Why does the calculator need the nominal size?
The js6 deviations are tabulated by nominal-size band, and the IT6 width also depends on size. Entering the size lets the calculator select the correct band and return the applicable upper and lower deviations.