EngineeringFits中文 / Chinese version ↗

The engineering workbench / fits and machine elements

ISO 286 h6 Shaft Tolerance Class: Nominal-Size Limit

Look up h6 shaft upper and lower deviations in micrometres, plus minimum and maximum sizes in millimetres. Values reuse the existing English ISO 286 dataset.

Table intervals cover nominal sizes greater than 0 and up to 500 mm. The existing English calculator supports 1–500 mm; results below 1 mm require verification.

02 / Read the limits

Results

Deviations in µm; nominal and limit sizes in mm.

CharacteristicResult · µm / mmInterpretation
Nominal size25 mmEnglish ISO 286 dataset.
Upper deviation0 µmHole ES / shaft es.
Lower deviation-13 µmHole EI / shaft ei.
Minimum size24.987 mmNominal + lower deviation / 1000.
Maximum size25 mmNominal + upper deviation / 1000.

A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.

h6 shaft size-range table

Nominal size > lower to ≤ upper · mmUpper deviation · µmLower deviation · µmVerification note
>0 to ≤30-6Below 1 mm NEEDS VERIFICATION
>3 to ≤60-8English dataset
>6 to ≤100-9English dataset
>10 to ≤180-11English dataset
>18 to ≤300-13English dataset
>30 to ≤500-16English dataset
>50 to ≤800-19English dataset
>80 to ≤1200-22English dataset
>120 to ≤1800-25English dataset
>180 to ≤2500-29English dataset
>250 to ≤3150-32English dataset
>315 to ≤4000-36English dataset
>400 to ≤5000-40English dataset

03 / How to use

How to use this calculator

  1. This page looks up the ISO 286 h6 shaft class. Enter the nominal size of the shaft in the field below; the class is already fixed for this page.
  2. Read the upper and lower limit deviations and the limits. For an h shaft, the upper limit should coincide with the nominal size.
  3. The size-range table on this page lists the same deviations for every tabulated band.
  4. To evaluate a fit with a mating hole such as H7, open the ISO 286 fit calculator and select both classes there. This page shows the h6 shaft limits only.
  5. Keep the result with the nominal size that produced it; the tabulated values change between size bands.

Table lookup, with explicit boundaries

Read the tabulated upper and lower deviations.
Minimum size = nominal + lower deviation / 1000.
Maximum size = nominal + upper deviation / 1000.
Deviations: µm; sizes: mm.

The first interval includes its lower tabulated size. Each following interval excludes its lower endpoint and includes its upper endpoint. The calculator rejects inputs outside the stated range and does not round inputs across a boundary.

04 / Engineering context

ISO 286 h6 Shaft Tolerance Class: Nominal-Size Limit

An h6 shaft is a shaft tolerance class in ISO 286. The lowercase h fixes the upper limit at the nominal size, so every permitted shaft size lies at or below that value. The 6 is the IT6 grade and sets the width of the zone. Compared with h7, the h6 band is narrower; both share the same nominal-size upper limit, but h6 removes more variation.

h6 is common in close clearance and location fits. H7/h6 is widely used where parts must be located accurately but assembled without interference; at the extreme, the hole and shaft meet line-to-line, and everywhere else there is clearance. The class is also used on located shafts, spigots and fixture details that need a controlled outside size, though the application and the mating hole still decide the fit. A tight size band does not guarantee a tight assembly if the hole class is loose.

h6 is a size class, not a complete functional specification. It does not control straightness, roundness, taper or surface texture, and it does not set the fit by itself: the mating hole does. Where an application depends on those characteristics, add the appropriate GPS or GD&T requirements and check the fit with the actual hole class.

ISO 286 data source

Numerical source: existing ISO 286 JSON, with the h/H, js, f/g and k/p rules in the existing engine. Dataset edition label: ISO 286-1:2010 / ISO 286-2:2010. This lookup adds no new fundamental-deviation formula.

06 / Questions

Frequently asked questions

What does h6 mean?

The h is the shaft fundamental deviation whose upper limit is at the nominal size. The 6 is the IT6 standard tolerance grade and determines the width of the shaft zone. Together they define the h6 shaft class.

Where is the upper limit of an h6 shaft?

It is at the nominal size. The lower limit is below it by the IT6 tolerance for that nominal size, so a conforming h6 shaft does not exceed the nominal size.

Is H7/h6 a clearance fit?

Yes. The H7 hole starts at the nominal size, and the h6 shaft ends at the nominal size, so the pair can be line-to-line at its tightest but cannot have interference. The actual clearance range depends on the nominal size and the two tolerance widths.

How does h6 differ from h7?

Both are h shafts with their upper limit at the nominal size. h6 uses the narrower IT6 grade and h7 uses the wider IT7 grade. h6 therefore gives less permitted shaft variation and generally a tighter assembly.

Is h6 a shaft-basis tolerance?

The letter h is the reference shaft in the shaft-basis system, but h6 is only a class. A fit is shaft-basis when the design keeps the shaft at h and varies the hole class. An h6 shaft can be used in either arrangement.

Does h6 specify a manufacturing process?

No. A tolerance class states the permitted size limits, not how to achieve them. Grinding, turning, honing or another process may be capable of the class, but the choice depends on material, size, quantity and the rest of the specification.

Does h6 control roundness or surface finish?

No. h6 controls size. Roundness, cylindricity, straightness and surface texture need separate requirements when they affect the function or the fit.

Why do the deviations change with size?

The h6 limit deviations depend on the nominal size and are tabulated in ISO 286-2. This page lists those values in the size-range table, and the calculator applies the class to the size you enter so the result matches the correct size band.