EngineeringFits中文 / Chinese version ↗

The engineering workbench / fits and machine elements

25 mm Shaft Keyway: Parallel Key and Keyway Dimensions

Find parallel key b × h, shaft groove depth t1, hub groove depth t2, groove-width deviations and the dimensions d − t1 and d + t2 for a 25 mm shaft.

GB/T 1095-2003 dimensions from the committed Chinese tool, shaft diameters 6–500 mm. DIN 6885-1 / ISO R773 comparison is pending; no interchangeable dimensions are asserted.

SECTION · GB/T 1095-2003⌀25 mm shaft
Parallel key and keyway section for a 25 mm shaftCross-section through a 25 mm shaft and its hub with a 8 by 7 mm parallel key. The key width b is 8 mm, the shaft keyway depth t1 is 4 mm and the hub keyway depth t2 is 3.3 mm, from the GB/T 1095-2003 table used by this page. Proportions follow these values.b = 8t2 = 3.3t1 = 4⌀d = 25HubShaft

8 × 7 key b × h, mm · GB/T 1095-2003 data; DIN 6885-1 to be verified

02 / Read the limits

Results

Dimensions and deviations in mm. Verification notes apply to the displayed source.

CharacteristicResult · mmInterpretation
Key b × h8 × 7 mmNominal parallel-key section.
Shaft groove depth t14 mmDepth allowance +0.2 / 0 mm in the source.
Hub groove depth t23.3 mmDepth allowance +0.2 / 0 mm in the source.
Shaft dimension d − t121 mmDeviation 0 / −0.2 mm on this dimension.
Hub dimension d + t228.3 mmDeviation +0.2 / 0 mm on this dimension.
Shaft groove width N90 / -0.036 mmUpper / lower deviations from nominal b.
Hub groove width JS9+0.018 / -0.018 mmUpper / lower deviations from nominal b.
Groove root radius0.25–0.4 mmTabulated minimum–maximum.

A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.

Parallel key and groove dimensions

Shaft d · mm (upper inclusive)Key b × h · mmt1 · mmt2 · mmDepth allowances t1 / t2 · mmRoot radius · mm
≥6 to ≤82 × 21.21+0.1/0; +0.1/00.08–0.16
>8 to ≤103 × 31.81.4+0.1/0; +0.1/00.08–0.16
>10 to ≤124 × 42.51.8+0.1/0; +0.1/00.16–0.25
>12 to ≤175 × 532.3+0.1/0; +0.1/00.16–0.25
>17 to ≤226 × 63.52.8+0.1/0; +0.1/00.16–0.25
>22 to ≤308 × 743.3+0.2/0; +0.2/00.25–0.4
>30 to ≤3810 × 853.3+0.2/0; +0.2/00.25–0.4
>38 to ≤4412 × 853.3+0.2/0; +0.2/00.25–0.4
>44 to ≤5014 × 95.53.8+0.2/0; +0.2/00.25–0.4
>50 to ≤5816 × 1064.3+0.2/0; +0.2/00.25–0.4
>58 to ≤6518 × 1174.4+0.2/0; +0.2/00.25–0.4
>65 to ≤7520 × 127.54.9+0.2/0; +0.2/00.4–0.6
>75 to ≤8522 × 1495.4+0.2/0; +0.2/00.4–0.6
>85 to ≤9525 × 1495.4+0.2/0; +0.2/00.4–0.6
>95 to ≤11028 × 16106.4+0.2/0; +0.2/00.4–0.6
>110 to ≤13032 × 18117.4+0.3/0; +0.3/00.7–1
>130 to ≤15036 × 20128.4+0.3/0; +0.3/00.7–1
>150 to ≤17040 × 22139.4+0.3/0; +0.3/00.7–1
>170 to ≤20045 × 251510.4+0.3/0; +0.3/00.7–1
>200 to ≤23050 × 281711.4+0.3/0; +0.3/00.7–1
>230 to ≤26056 × 322012.4+0.3/0; +0.3/01.2–1.6
>260 to ≤29063 × 322012.4+0.3/0; +0.3/01.2–1.6
>290 to ≤33070 × 362214.4+0.3/0; +0.3/01.2–1.6
>330 to ≤38080 × 402515.4+0.3/0; +0.3/02–2.5
>380 to ≤44090 × 452817.4+0.3/0; +0.3/02–2.5
>440 to ≤500100 × 503119.5+0.3/0; +0.3/02–2.5

Groove-width deviations

All entries are upper / lower deviations in mm from nominal key width b. This is the groove width, not the key’s own width tolerance.

b · mmH9D10N9JS9P9
2+0.025 / 0+0.06 / +0.02-0.004 / -0.029+0.0125 / -0.0125-0.006 / -0.031
3+0.025 / 0+0.06 / +0.02-0.004 / -0.029+0.0125 / -0.0125-0.006 / -0.031
4+0.03 / 0+0.078 / +0.030 / -0.03+0.015 / -0.015-0.012 / -0.042
5+0.03 / 0+0.078 / +0.030 / -0.03+0.015 / -0.015-0.012 / -0.042
6+0.03 / 0+0.078 / +0.030 / -0.03+0.015 / -0.015-0.012 / -0.042
8+0.036 / 0+0.098 / +0.040 / -0.036+0.018 / -0.018-0.015 / -0.051
10+0.036 / 0+0.098 / +0.040 / -0.036+0.018 / -0.018-0.015 / -0.051
12+0.043 / 0+0.12 / +0.050 / -0.043+0.0215 / -0.0215-0.018 / -0.061
14+0.043 / 0+0.12 / +0.050 / -0.043+0.0215 / -0.0215-0.018 / -0.061
16+0.043 / 0+0.12 / +0.050 / -0.043+0.0215 / -0.0215-0.018 / -0.061
18+0.043 / 0+0.12 / +0.050 / -0.043+0.0215 / -0.0215-0.018 / -0.061
20+0.052 / 0+0.149 / +0.0650 / -0.052+0.026 / -0.026-0.022 / -0.074
22+0.052 / 0+0.149 / +0.0650 / -0.052+0.026 / -0.026-0.022 / -0.074
25+0.052 / 0+0.149 / +0.0650 / -0.052+0.026 / -0.026-0.022 / -0.074
28+0.052 / 0+0.149 / +0.0650 / -0.052+0.026 / -0.026-0.022 / -0.074
32+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
36+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
40+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
45+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
50+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
56+0.074 / 0+0.22 / +0.10 / -0.074+0.037 / -0.037-0.032 / -0.106
63+0.074 / 0+0.22 / +0.10 / -0.074+0.037 / -0.037-0.032 / -0.106
70+0.074 / 0+0.22 / +0.10 / -0.074+0.037 / -0.037-0.032 / -0.106
80+0.087 / 0+0.26 / +0.120 / -0.087+0.0435 / -0.0435-0.037 / -0.124
90+0.087 / 0+0.26 / +0.120 / -0.087+0.0435 / -0.0435-0.037 / -0.124
100+0.087 / 0+0.26 / +0.120 / -0.087+0.0435 / -0.0435-0.037 / -0.124

03 / How to use

How to use this calculator

  1. This calculator uses the GB/T 1095-2003 keyway table from the site's Chinese tool. DIN 6885-1 and ISO/R 773 values have not been verified against it, so confirm the standard named on the drawing first.
  2. Enter 25 mm as the nominal shaft diameter.
  3. Choose the connection (loose, normal or tight); it sets the shaft and hub groove-width tolerance codes.
  4. Read the key cross-section, shaft keyway, hub keyway and tolerance values from the result.
  5. Compare the result with any individual note on the drawing before machining or ordering a key.

Table lookup, with explicit boundaries

Select the shaft-diameter interval → read b, h, t1 and t2.
Shaft dimension = d − t1, with deviation 0 / −t1 allowance.
Hub dimension = d + t2, with deviation +t2 allowance / 0.
Groove-width deviations apply to nominal b, not shaft diameter d.

The source accepts 6 mm in its first interval (6–8 mm). Following intervals exclude the lower endpoint and include the upper endpoint. In particular, 30 mm uses the >22–30 mm row. Inputs outside 6–500 mm are rejected.

04 / Engineering context

Keyway for a 25 mm Shaft: Parallel Key and Keyway Dimensions

A 25 mm shaft sits in the small-to-medium range of power transmission work: pump drives, gearbox inputs, fan shafts and similar assemblies. The keyway has to transmit torque without preventing the hub from seating squarely or being removed for service. Its size comes from the standard's diameter table, not from scaling a smaller or larger shaft by eye.

The keyway also interacts with the fits around it. The shaft and hub bore tolerances, the side fit of the key, and the clearance at the top of the key all affect assembly and running behaviour. A key that is forced into a tight slot can distort a hub; one that is too loose can allow backlash and fretting. The standard defines the keyway dimensions and tolerances, but the designer still has to choose fits that suit the duty.

DIN 6885, ISO/R 773 and GB/T 1095 use related lookup logic, yet each is a separate document with its own edition. Confirm which one governs the drawing before using a value, and do not carry a dimension across from a 20 mm or 30 mm shaft on the assumption that it will be close enough. The exact key width, height, keyway depths and tolerances for a 25 mm shaft are shown in the on-page calculator result.

GB / DIN / ISO comparison status

StandardData used / status
GB/T 1095-2003Committed /keyway/ dimensions and width-tolerance values.
DIN 6885-1NEEDS VERIFICATION: no independent DIN table in the site dataset.
ISO R773NEEDS VERIFICATION: dimensional relationship and edition must be checked.

No numerical DIN-versus-GB differences are inferred. Source: Chinese GB/T 1095 tool.

06 / Questions

Frequently asked questions

What keyway size does a 25 mm shaft need?

The size is defined by the GB/T 1095 table used here for a 25 mm nominal shaft. There is no universal answer that applies across DIN, ISO and GB systems or across different key types. Confirm the drawing's standard and key type, enter 25 mm, and read the exact dimensions from the calculator result.

What key width and height fit a 25 mm shaft?

The calculator returns the nominal key width and height for a 25 mm shaft in the GB/T 1095 table used here. Do not infer them by scaling from another diameter, because standard tables use bands and the values do not change in a simple proportion. Use the result together with the drawing callout.

Are DIN 6885, ISO/R 773 and GB/T 1095 identical for a 25 mm shaft?

The Chinese national standards catalogue (SAMR) lists GB/T 1095-2003 as a non-equivalent (NEQ) adoption of ASME B18.25.1M:1996; any relationship to ISO/R 773 is to be verified, and separate editions can still differ in detail. Separate editions can still differ in detail, and DIN 6885 is its own document. Treat the standard named on the drawing as authoritative rather than mixing values from all three.

How deep is the keyway on a 25 mm shaft?

The shaft and hub depths are part of the standard lookup and are shown by the on-page calculator for a 25 mm shaft. They are not repeated here because the result depends on the standard and key type; this calculator shows GB/T 1095 values only. A deeper keyway removes more material, so review the shaft stress where the duty is demanding.

How long should the keyway be on a 25 mm shaft?

Length is governed by the hub, the torque to be transmitted, the permissible bearing pressure and the key material. It is not fixed by the 25 mm diameter alone. Use the drawing length or complete a separate design check; the cross-section lookup only gives the key and keyway section.

What about the hub keyway for a 25 mm shaft?

The hub keyway is part of the same standard lookup and is returned with the shaft keyway values. It must be machined to the correct depth and width for the key in the result, and its edge condition matters for fatigue and for hub distortion. Confirm both the shaft and hub results before cutting either part.

Can I use the same key on a 20 mm and a 25 mm shaft?

No. A 25 mm shaft can fall in a different diameter band with a different key cross-section, and the keyway depths can differ as well. Even where the nominal key looks similar, the fits and tolerances may not match. Select the key from the 25 mm result, not from a key that happened to fit another shaft.