EngineeringFits中文 / Chinese version ↗

The engineering workbench / fits and machine elements

50 mm Shaft Keyway: Parallel Key and Keyway Dimensions

Find parallel key b × h, shaft groove depth t1, hub groove depth t2, groove-width deviations and the dimensions d − t1 and d + t2 for a 50 mm shaft.

GB/T 1095-2003 dimensions from the committed Chinese tool, shaft diameters 6–500 mm. DIN 6885-1 / ISO R773 comparison is pending; no interchangeable dimensions are asserted.

SECTION · GB/T 1095-2003⌀50 mm shaft
Parallel key and keyway section for a 50 mm shaftCross-section through a 50 mm shaft and its hub with a 14 by 9 mm parallel key. The key width b is 14 mm, the shaft keyway depth t1 is 5.5 mm and the hub keyway depth t2 is 3.8 mm, from the GB/T 1095-2003 table used by this page. Proportions follow these values.b = 14t2 = 3.8t1 = 5.5⌀d = 50HubShaft

14 × 9 key b × h, mm · GB/T 1095-2003 data; DIN 6885-1 to be verified

02 / Read the limits

Results

Dimensions and deviations in mm. Verification notes apply to the displayed source.

CharacteristicResult · mmInterpretation
Key b × h14 × 9 mmNominal parallel-key section.
Shaft groove depth t15.5 mmDepth allowance +0.2 / 0 mm in the source.
Hub groove depth t23.8 mmDepth allowance +0.2 / 0 mm in the source.
Shaft dimension d − t144.5 mmDeviation 0 / −0.2 mm on this dimension.
Hub dimension d + t253.8 mmDeviation +0.2 / 0 mm on this dimension.
Shaft groove width N90 / -0.043 mmUpper / lower deviations from nominal b.
Hub groove width JS9+0.0215 / -0.0215 mmUpper / lower deviations from nominal b.
Groove root radius0.25–0.4 mmTabulated minimum–maximum.

A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.

Parallel key and groove dimensions

Shaft d · mm (upper inclusive)Key b × h · mmt1 · mmt2 · mmDepth allowances t1 / t2 · mmRoot radius · mm
≥6 to ≤82 × 21.21+0.1/0; +0.1/00.08–0.16
>8 to ≤103 × 31.81.4+0.1/0; +0.1/00.08–0.16
>10 to ≤124 × 42.51.8+0.1/0; +0.1/00.16–0.25
>12 to ≤175 × 532.3+0.1/0; +0.1/00.16–0.25
>17 to ≤226 × 63.52.8+0.1/0; +0.1/00.16–0.25
>22 to ≤308 × 743.3+0.2/0; +0.2/00.25–0.4
>30 to ≤3810 × 853.3+0.2/0; +0.2/00.25–0.4
>38 to ≤4412 × 853.3+0.2/0; +0.2/00.25–0.4
>44 to ≤5014 × 95.53.8+0.2/0; +0.2/00.25–0.4
>50 to ≤5816 × 1064.3+0.2/0; +0.2/00.25–0.4
>58 to ≤6518 × 1174.4+0.2/0; +0.2/00.25–0.4
>65 to ≤7520 × 127.54.9+0.2/0; +0.2/00.4–0.6
>75 to ≤8522 × 1495.4+0.2/0; +0.2/00.4–0.6
>85 to ≤9525 × 1495.4+0.2/0; +0.2/00.4–0.6
>95 to ≤11028 × 16106.4+0.2/0; +0.2/00.4–0.6
>110 to ≤13032 × 18117.4+0.3/0; +0.3/00.7–1
>130 to ≤15036 × 20128.4+0.3/0; +0.3/00.7–1
>150 to ≤17040 × 22139.4+0.3/0; +0.3/00.7–1
>170 to ≤20045 × 251510.4+0.3/0; +0.3/00.7–1
>200 to ≤23050 × 281711.4+0.3/0; +0.3/00.7–1
>230 to ≤26056 × 322012.4+0.3/0; +0.3/01.2–1.6
>260 to ≤29063 × 322012.4+0.3/0; +0.3/01.2–1.6
>290 to ≤33070 × 362214.4+0.3/0; +0.3/01.2–1.6
>330 to ≤38080 × 402515.4+0.3/0; +0.3/02–2.5
>380 to ≤44090 × 452817.4+0.3/0; +0.3/02–2.5
>440 to ≤500100 × 503119.5+0.3/0; +0.3/02–2.5

Groove-width deviations

All entries are upper / lower deviations in mm from nominal key width b. This is the groove width, not the key’s own width tolerance.

b · mmH9D10N9JS9P9
2+0.025 / 0+0.06 / +0.02-0.004 / -0.029+0.0125 / -0.0125-0.006 / -0.031
3+0.025 / 0+0.06 / +0.02-0.004 / -0.029+0.0125 / -0.0125-0.006 / -0.031
4+0.03 / 0+0.078 / +0.030 / -0.03+0.015 / -0.015-0.012 / -0.042
5+0.03 / 0+0.078 / +0.030 / -0.03+0.015 / -0.015-0.012 / -0.042
6+0.03 / 0+0.078 / +0.030 / -0.03+0.015 / -0.015-0.012 / -0.042
8+0.036 / 0+0.098 / +0.040 / -0.036+0.018 / -0.018-0.015 / -0.051
10+0.036 / 0+0.098 / +0.040 / -0.036+0.018 / -0.018-0.015 / -0.051
12+0.043 / 0+0.12 / +0.050 / -0.043+0.0215 / -0.0215-0.018 / -0.061
14+0.043 / 0+0.12 / +0.050 / -0.043+0.0215 / -0.0215-0.018 / -0.061
16+0.043 / 0+0.12 / +0.050 / -0.043+0.0215 / -0.0215-0.018 / -0.061
18+0.043 / 0+0.12 / +0.050 / -0.043+0.0215 / -0.0215-0.018 / -0.061
20+0.052 / 0+0.149 / +0.0650 / -0.052+0.026 / -0.026-0.022 / -0.074
22+0.052 / 0+0.149 / +0.0650 / -0.052+0.026 / -0.026-0.022 / -0.074
25+0.052 / 0+0.149 / +0.0650 / -0.052+0.026 / -0.026-0.022 / -0.074
28+0.052 / 0+0.149 / +0.0650 / -0.052+0.026 / -0.026-0.022 / -0.074
32+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
36+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
40+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
45+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
50+0.062 / 0+0.18 / +0.080 / -0.062+0.031 / -0.031-0.026 / -0.088
56+0.074 / 0+0.22 / +0.10 / -0.074+0.037 / -0.037-0.032 / -0.106
63+0.074 / 0+0.22 / +0.10 / -0.074+0.037 / -0.037-0.032 / -0.106
70+0.074 / 0+0.22 / +0.10 / -0.074+0.037 / -0.037-0.032 / -0.106
80+0.087 / 0+0.26 / +0.120 / -0.087+0.0435 / -0.0435-0.037 / -0.124
90+0.087 / 0+0.26 / +0.120 / -0.087+0.0435 / -0.0435-0.037 / -0.124
100+0.087 / 0+0.26 / +0.120 / -0.087+0.0435 / -0.0435-0.037 / -0.124

03 / How to use

How to use this calculator

  1. This calculator uses the GB/T 1095-2003 keyway table from the site's Chinese tool. DIN 6885-1 and ISO/R 773 values have not been verified against it, so confirm the standard named on the drawing first.
  2. Enter 50 mm as the nominal shaft diameter.
  3. Choose the connection (loose, normal or tight); it sets the shaft and hub groove-width tolerance codes.
  4. Read the key cross-section, shaft keyway, hub keyway and tolerance values from the result.
  5. Check the drawing for individual requirements on fit, key length, material and inspection before machining.

Table lookup, with explicit boundaries

Select the shaft-diameter interval → read b, h, t1 and t2.
Shaft dimension = d − t1, with deviation 0 / −t1 allowance.
Hub dimension = d + t2, with deviation +t2 allowance / 0.
Groove-width deviations apply to nominal b, not shaft diameter d.

The source accepts 6 mm in its first interval (6–8 mm). Following intervals exclude the lower endpoint and include the upper endpoint. In particular, 30 mm uses the >22–30 mm row. Inputs outside 6–500 mm are rejected.

04 / Engineering context

Keyway for a 50 mm Shaft: Parallel Key and Keyway Dimensions

A 50 mm shaft is a substantial drive member, used on heavy conveyors, large pumps, crushers and industrial gear units. At this size the key and keyway carry a large torque, and the consequences of a poor fit are correspondingly greater. The dimensions still come from the standard's table, not from a rule based on the shaft diameter.

The keyway must be machined to the correct width, depth and edge condition, but dimensions alone do not guarantee a good joint. The hub bore, shaft fit, key length and contact pattern all affect how the load is shared. On a 50 mm shaft, a key that sits high or bears on one corner can concentrate load and cause movement, heating or fretting. Inspection before assembly is worthwhile, especially after repair or rework.

DIN 6885, ISO/R 773 and GB/T 1095 use related lookup logic but are separate standards with their own editions and tolerances. Confirm the drawing's reference before machining a replacement part. The exact key width, height, keyway depths and tolerances for a 50 mm shaft are given by the on-page calculator, so read them from the result rather than carrying over a dimension from a smaller shaft.

GB / DIN / ISO comparison status

StandardData used / status
GB/T 1095-2003Committed /keyway/ dimensions and width-tolerance values.
DIN 6885-1NEEDS VERIFICATION: no independent DIN table in the site dataset.
ISO R773NEEDS VERIFICATION: dimensional relationship and edition must be checked.

No numerical DIN-versus-GB differences are inferred. Source: Chinese GB/T 1095 tool.

06 / Questions

Frequently asked questions

What keyway size does a 50 mm shaft need?

The correct size is the table entry for a 50 mm nominal shaft under the governing standard. It is not universal across standards or key types. Confirm the drawing's standard, enter 50 mm in the calculator, and read the key and keyway values shown for that diameter.

What key width and height fit a 50 mm shaft?

The calculator result gives the nominal key width and height for a 50 mm shaft. Do not assume that a key from a smaller or larger shaft will fit, and do not scale dimensions by eye. Confirm the key type as well as the size before ordering or making the key.

How deep is the keyway on a 50 mm shaft?

Shaft and hub keyway depths are part of the standard lookup and are displayed by the calculator for a 50 mm shaft. They are not restated here because they depend on the standard and key type. Because a 50 mm shaft may carry high loads, consider the keyway's stress concentration and the remaining section in the design check.

How long should the keyway be on a 50 mm shaft?

Key length depends on the hub, torque, bearing pressure, key material and duty. The 50 mm diameter does not set it by itself. Use the drawing length or confirm it with a design check, and make sure the keyway does not run into a shoulder or seal area where it would create an unintended stress riser.

Are DIN 6885, ISO/R 773 and GB/T 1095 identical for a 50 mm shaft?

The Chinese national standards catalogue (SAMR) lists GB/T 1095-2003 as a non-equivalent (NEQ) adoption of ASME B18.25.1M:1996; any relationship to ISO/R 773 is to be verified, and separate editions can still differ in detail. The drawing or contract decides which applies. Do not mix dimensions or tolerances from different documents merely because they describe similar parallel keys.

Can a 50 mm shaft keyway carry high torque?

The keyway can be part of a high-torque design, but capacity is not determined by diameter or keyway dimensions alone. Shaft and key material, heat treatment, fit, key length, hub strength, load reversals and safety factors all matter. For a heavily loaded 50 mm drive, complete a proper engineering check rather than relying on the table lookup.

What about the hub keyway for a 50 mm shaft?

It must be machined to the matching standard values and checked for size, alignment and edge condition. A tight or distorted hub keyway can prevent the hub from seating, while a loose one can allow fretting. Read both shaft and hub values from the 50 mm result, and inspect the bore before assembly.

How do I inspect a keyway on a 50 mm shaft before assembly?

Clean the shaft and hub, remove burrs carefully, and check the keyway width, depth, edges and alignment against the drawing and calculator result. Look for cracks, fretting or deformation, particularly after a repair. If the shaft has been welded, bent or heavily loaded, have its condition assessed before returning it to service.