The engineering workbench / fits and machine elements
20 mm Shaft Keyway: Parallel Key and Keyway Dimensions
Find parallel key b × h, shaft groove depth t1, hub groove depth t2, groove-width deviations and the dimensions d − t1 and d + t2 for a 20 mm shaft.
GB/T 1095-2003 dimensions from the committed Chinese tool, shaft diameters 6–500 mm. DIN 6885-1 / ISO R773 comparison is pending; no interchangeable dimensions are asserted.
6 × 6 key b × h, mm · GB/T 1095-2003 data; DIN 6885-1 to be verified
02 / Read the limits
Results
Dimensions and deviations in mm. Verification notes apply to the displayed source.
| Characteristic | Result · mm | Interpretation |
|---|---|---|
| Key b × h | 6 × 6 mm | Nominal parallel-key section. |
| Shaft groove depth t1 | 3.5 mm | Depth allowance +0.1 / 0 mm in the source. |
| Hub groove depth t2 | 2.8 mm | Depth allowance +0.1 / 0 mm in the source. |
| Shaft dimension d − t1 | 16.5 mm | Deviation 0 / −0.1 mm on this dimension. |
| Hub dimension d + t2 | 22.8 mm | Deviation +0.1 / 0 mm on this dimension. |
| Shaft groove width N9 | 0 / -0.03 mm | Upper / lower deviations from nominal b. |
| Hub groove width JS9 | +0.015 / -0.015 mm | Upper / lower deviations from nominal b. |
| Groove root radius | 0.16–0.25 mm | Tabulated minimum–maximum. |
A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.
Parallel key and groove dimensions
| Shaft d · mm (upper inclusive) | Key b × h · mm | t1 · mm | t2 · mm | Depth allowances t1 / t2 · mm | Root radius · mm |
|---|---|---|---|---|---|
| ≥6 to ≤8 | 2 × 2 | 1.2 | 1 | +0.1/0; +0.1/0 | 0.08–0.16 |
| >8 to ≤10 | 3 × 3 | 1.8 | 1.4 | +0.1/0; +0.1/0 | 0.08–0.16 |
| >10 to ≤12 | 4 × 4 | 2.5 | 1.8 | +0.1/0; +0.1/0 | 0.16–0.25 |
| >12 to ≤17 | 5 × 5 | 3 | 2.3 | +0.1/0; +0.1/0 | 0.16–0.25 |
| >17 to ≤22 | 6 × 6 | 3.5 | 2.8 | +0.1/0; +0.1/0 | 0.16–0.25 |
| >22 to ≤30 | 8 × 7 | 4 | 3.3 | +0.2/0; +0.2/0 | 0.25–0.4 |
| >30 to ≤38 | 10 × 8 | 5 | 3.3 | +0.2/0; +0.2/0 | 0.25–0.4 |
| >38 to ≤44 | 12 × 8 | 5 | 3.3 | +0.2/0; +0.2/0 | 0.25–0.4 |
| >44 to ≤50 | 14 × 9 | 5.5 | 3.8 | +0.2/0; +0.2/0 | 0.25–0.4 |
| >50 to ≤58 | 16 × 10 | 6 | 4.3 | +0.2/0; +0.2/0 | 0.25–0.4 |
| >58 to ≤65 | 18 × 11 | 7 | 4.4 | +0.2/0; +0.2/0 | 0.25–0.4 |
| >65 to ≤75 | 20 × 12 | 7.5 | 4.9 | +0.2/0; +0.2/0 | 0.4–0.6 |
| >75 to ≤85 | 22 × 14 | 9 | 5.4 | +0.2/0; +0.2/0 | 0.4–0.6 |
| >85 to ≤95 | 25 × 14 | 9 | 5.4 | +0.2/0; +0.2/0 | 0.4–0.6 |
| >95 to ≤110 | 28 × 16 | 10 | 6.4 | +0.2/0; +0.2/0 | 0.4–0.6 |
| >110 to ≤130 | 32 × 18 | 11 | 7.4 | +0.3/0; +0.3/0 | 0.7–1 |
| >130 to ≤150 | 36 × 20 | 12 | 8.4 | +0.3/0; +0.3/0 | 0.7–1 |
| >150 to ≤170 | 40 × 22 | 13 | 9.4 | +0.3/0; +0.3/0 | 0.7–1 |
| >170 to ≤200 | 45 × 25 | 15 | 10.4 | +0.3/0; +0.3/0 | 0.7–1 |
| >200 to ≤230 | 50 × 28 | 17 | 11.4 | +0.3/0; +0.3/0 | 0.7–1 |
| >230 to ≤260 | 56 × 32 | 20 | 12.4 | +0.3/0; +0.3/0 | 1.2–1.6 |
| >260 to ≤290 | 63 × 32 | 20 | 12.4 | +0.3/0; +0.3/0 | 1.2–1.6 |
| >290 to ≤330 | 70 × 36 | 22 | 14.4 | +0.3/0; +0.3/0 | 1.2–1.6 |
| >330 to ≤380 | 80 × 40 | 25 | 15.4 | +0.3/0; +0.3/0 | 2–2.5 |
| >380 to ≤440 | 90 × 45 | 28 | 17.4 | +0.3/0; +0.3/0 | 2–2.5 |
| >440 to ≤500 | 100 × 50 | 31 | 19.5 | +0.3/0; +0.3/0 | 2–2.5 |
Groove-width deviations
All entries are upper / lower deviations in mm from nominal key width b. This is the groove width, not the key’s own width tolerance.
| b · mm | H9 | D10 | N9 | JS9 | P9 |
|---|---|---|---|---|---|
| 2 | +0.025 / 0 | +0.06 / +0.02 | -0.004 / -0.029 | +0.0125 / -0.0125 | -0.006 / -0.031 |
| 3 | +0.025 / 0 | +0.06 / +0.02 | -0.004 / -0.029 | +0.0125 / -0.0125 | -0.006 / -0.031 |
| 4 | +0.03 / 0 | +0.078 / +0.03 | 0 / -0.03 | +0.015 / -0.015 | -0.012 / -0.042 |
| 5 | +0.03 / 0 | +0.078 / +0.03 | 0 / -0.03 | +0.015 / -0.015 | -0.012 / -0.042 |
| 6 | +0.03 / 0 | +0.078 / +0.03 | 0 / -0.03 | +0.015 / -0.015 | -0.012 / -0.042 |
| 8 | +0.036 / 0 | +0.098 / +0.04 | 0 / -0.036 | +0.018 / -0.018 | -0.015 / -0.051 |
| 10 | +0.036 / 0 | +0.098 / +0.04 | 0 / -0.036 | +0.018 / -0.018 | -0.015 / -0.051 |
| 12 | +0.043 / 0 | +0.12 / +0.05 | 0 / -0.043 | +0.0215 / -0.0215 | -0.018 / -0.061 |
| 14 | +0.043 / 0 | +0.12 / +0.05 | 0 / -0.043 | +0.0215 / -0.0215 | -0.018 / -0.061 |
| 16 | +0.043 / 0 | +0.12 / +0.05 | 0 / -0.043 | +0.0215 / -0.0215 | -0.018 / -0.061 |
| 18 | +0.043 / 0 | +0.12 / +0.05 | 0 / -0.043 | +0.0215 / -0.0215 | -0.018 / -0.061 |
| 20 | +0.052 / 0 | +0.149 / +0.065 | 0 / -0.052 | +0.026 / -0.026 | -0.022 / -0.074 |
| 22 | +0.052 / 0 | +0.149 / +0.065 | 0 / -0.052 | +0.026 / -0.026 | -0.022 / -0.074 |
| 25 | +0.052 / 0 | +0.149 / +0.065 | 0 / -0.052 | +0.026 / -0.026 | -0.022 / -0.074 |
| 28 | +0.052 / 0 | +0.149 / +0.065 | 0 / -0.052 | +0.026 / -0.026 | -0.022 / -0.074 |
| 32 | +0.062 / 0 | +0.18 / +0.08 | 0 / -0.062 | +0.031 / -0.031 | -0.026 / -0.088 |
| 36 | +0.062 / 0 | +0.18 / +0.08 | 0 / -0.062 | +0.031 / -0.031 | -0.026 / -0.088 |
| 40 | +0.062 / 0 | +0.18 / +0.08 | 0 / -0.062 | +0.031 / -0.031 | -0.026 / -0.088 |
| 45 | +0.062 / 0 | +0.18 / +0.08 | 0 / -0.062 | +0.031 / -0.031 | -0.026 / -0.088 |
| 50 | +0.062 / 0 | +0.18 / +0.08 | 0 / -0.062 | +0.031 / -0.031 | -0.026 / -0.088 |
| 56 | +0.074 / 0 | +0.22 / +0.1 | 0 / -0.074 | +0.037 / -0.037 | -0.032 / -0.106 |
| 63 | +0.074 / 0 | +0.22 / +0.1 | 0 / -0.074 | +0.037 / -0.037 | -0.032 / -0.106 |
| 70 | +0.074 / 0 | +0.22 / +0.1 | 0 / -0.074 | +0.037 / -0.037 | -0.032 / -0.106 |
| 80 | +0.087 / 0 | +0.26 / +0.12 | 0 / -0.087 | +0.0435 / -0.0435 | -0.037 / -0.124 |
| 90 | +0.087 / 0 | +0.26 / +0.12 | 0 / -0.087 | +0.0435 / -0.0435 | -0.037 / -0.124 |
| 100 | +0.087 / 0 | +0.26 / +0.12 | 0 / -0.087 | +0.0435 / -0.0435 | -0.037 / -0.124 |
03 / How to use
How to use this calculator
- This calculator uses the GB/T 1095-2003 keyway table from the site's Chinese tool. DIN 6885-1 and ISO/R 773 values have not been verified against it, so confirm the standard named on the drawing first.
- Enter 20 mm as the nominal shaft diameter.
- Choose the connection (loose, normal or tight); it sets the shaft and hub groove-width tolerance codes.
- Read the key cross-section, shaft keyway, hub keyway and tolerance values from the result.
- Check the drawing for an individual keyway note, fit or material requirement before machining.
Table lookup, with explicit boundaries
Shaft dimension = d − t1, with deviation 0 / −t1 allowance.
Hub dimension = d + t2, with deviation +t2 allowance / 0.
Groove-width deviations apply to nominal b, not shaft diameter d.
The source accepts 6 mm in its first interval (6–8 mm). Following intervals exclude the lower endpoint and include the upper endpoint. In particular, 30 mm uses the >22–30 mm row. Inputs outside 6–500 mm are rejected.
04 / Engineering context
Keyway for a 20 mm Shaft: Parallel Key and Keyway Dimensions
A 20 mm shaft is a compact drive member, often found in small pumps, instruments, gearboxes and light conveyors. Its keyway is not sized by taking a fixed proportion of the shaft. The applicable standard maps the nominal diameter to a key cross-section and then to the shaft and hub keyway dimensions. This page is for a 20 mm nominal shaft, so use that value rather than a caliper reading from a worn or plated part.
At this diameter the keyway is a meaningful fraction of the shaft section, so seating and edge condition matter. The key should bear on its sides, the hub must seat or slide without binding, and the keyway edges should not become a starting point for cracks under shock or reversing load. Those checks depend on the shaft material, heat treatment and duty; a dimensional lookup alone cannot settle them.
Use the standard named on the drawing: DIN 6885, ISO/R 773 or GB/T 1095. The three use comparable lookup logic but are separate documents and editions, so do not take a figure from one and apply it to another without confirmation. The exact key width, height, keyway depths and tolerances for a 20 mm shaft are shown by the on-page calculator result. This text deliberately does not invent them.
GB / DIN / ISO comparison status
| Standard | Data used / status |
|---|---|
| GB/T 1095-2003 | Committed /keyway/ dimensions and width-tolerance values. |
| DIN 6885-1 | NEEDS VERIFICATION: no independent DIN table in the site dataset. |
| ISO R773 | NEEDS VERIFICATION: dimensional relationship and edition must be checked. |
No numerical DIN-versus-GB differences are inferred. Source: Chinese GB/T 1095 tool.
06 / Questions
Frequently asked questions
What keyway size does a 20 mm shaft need?
There is no single answer outside a named standard and key type. The 20 mm diameter selects a row in the applicable table, and that row gives the key and keyway dimensions. Confirm the standard named on the drawing, then enter 20 mm in the calculator to read the exact values for this shaft.
What key width and height fit a 20 mm shaft?
The calculator result gives the nominal width and height for a 20 mm shaft in the GB/T 1095 table used here. Do not assume that a key from a nearby shaft will fit, because the standard's diameter bands can change between sizes. Order or make the key from the result and the drawing, not from a rule of thumb.
Are DIN 6885, ISO/R 773 and GB/T 1095 values the same for a 20 mm shaft?
The Chinese national standards catalogue (SAMR) lists GB/T 1095-2003 as a non-equivalent (NEQ) adoption of ASME B18.25.1M:1996; any relationship to ISO/R 773 is to be verified, and separate editions can still differ in detail. Use the standard named on the drawing. If the drawing is silent, confirm the intended standard before cutting the keyway.
How deep is the keyway on a 20 mm shaft?
The depth is standard-dependent and is not repeated in this article. The on-page calculator returns the shaft and hub keyway depths for a 20 mm shaft in the GB/T 1095 table used here. Because the keyway removes material from a small shaft section, check the resulting stress concentration if the duty is severe.
How long should the keyway be on a 20 mm shaft?
Key length is a separate design choice based on hub length, torque, bearing pressure and key material. The cross-section lookup for a 20 mm shaft does not by itself set the length. Read the length from the drawing, or confirm it with a design check rather than assuming that any convenient key length is acceptable.
Can I use a measured diameter instead of 20 mm in the calculator?
Use the nominal 20 mm from the drawing for the standard lookup. A measured value describes the actual shaft, including wear, plating and manufacturing deviation, and belongs in a fit or condition assessment. Mixing a measured diameter into a nominal table can select the wrong row.
Is a 20 mm shaft strong enough with a keyway?
That cannot be answered from diameter alone. Shaft material, heat treatment, torque, bending, shock, reversing duty, keyway length and the rest of the geometry all contribute. The keyway reduces the section and adds stress concentration, so a responsible check is needed for demanding applications. The calculator supplies dimensions, not a strength rating.