The engineering workbench / fits and machine elements
30 mm Shaft Keyway: Parallel Key and Keyway Dimensions
Find parallel key b × h, shaft groove depth t1, hub groove depth t2, groove-width deviations and the dimensions d − t1 and d + t2 for a 30 mm shaft.
GB/T 1095-2003 dimensions from the committed Chinese tool, shaft diameters 6–500 mm. DIN 6885-1 / ISO R773 comparison is pending; no interchangeable dimensions are asserted.
8 × 7 key b × h, mm · GB/T 1095-2003 data; DIN 6885-1 to be verified
02 / Read the limits
Results
Dimensions and deviations in mm. Verification notes apply to the displayed source.
| Characteristic | Result · mm | Interpretation |
|---|---|---|
| Key b × h | 8 × 7 mm | Nominal parallel-key section. |
| Shaft groove depth t1 | 4 mm | Depth allowance +0.2 / 0 mm in the source. |
| Hub groove depth t2 | 3.3 mm | Depth allowance +0.2 / 0 mm in the source. |
| Shaft dimension d − t1 | 26 mm | Deviation 0 / −0.2 mm on this dimension. |
| Hub dimension d + t2 | 33.3 mm | Deviation +0.2 / 0 mm on this dimension. |
| Shaft groove width N9 | 0 / -0.036 mm | Upper / lower deviations from nominal b. |
| Hub groove width JS9 | +0.018 / -0.018 mm | Upper / lower deviations from nominal b. |
| Groove root radius | 0.25–0.4 mm | Tabulated minimum–maximum. |
A missing table entry is displayed as “No tabulated value”; values are never interpolated. Individual drawing requirements take precedence over a general lookup.
Parallel key and groove dimensions
| Shaft d · mm (upper inclusive) | Key b × h · mm | t1 · mm | t2 · mm | Depth allowances t1 / t2 · mm | Root radius · mm |
|---|---|---|---|---|---|
| ≥6 to ≤8 | 2 × 2 | 1.2 | 1 | +0.1/0; +0.1/0 | 0.08–0.16 |
| >8 to ≤10 | 3 × 3 | 1.8 | 1.4 | +0.1/0; +0.1/0 | 0.08–0.16 |
| >10 to ≤12 | 4 × 4 | 2.5 | 1.8 | +0.1/0; +0.1/0 | 0.16–0.25 |
| >12 to ≤17 | 5 × 5 | 3 | 2.3 | +0.1/0; +0.1/0 | 0.16–0.25 |
| >17 to ≤22 | 6 × 6 | 3.5 | 2.8 | +0.1/0; +0.1/0 | 0.16–0.25 |
| >22 to ≤30 | 8 × 7 | 4 | 3.3 | +0.2/0; +0.2/0 | 0.25–0.4 |
| >30 to ≤38 | 10 × 8 | 5 | 3.3 | +0.2/0; +0.2/0 | 0.25–0.4 |
| >38 to ≤44 | 12 × 8 | 5 | 3.3 | +0.2/0; +0.2/0 | 0.25–0.4 |
| >44 to ≤50 | 14 × 9 | 5.5 | 3.8 | +0.2/0; +0.2/0 | 0.25–0.4 |
| >50 to ≤58 | 16 × 10 | 6 | 4.3 | +0.2/0; +0.2/0 | 0.25–0.4 |
| >58 to ≤65 | 18 × 11 | 7 | 4.4 | +0.2/0; +0.2/0 | 0.25–0.4 |
| >65 to ≤75 | 20 × 12 | 7.5 | 4.9 | +0.2/0; +0.2/0 | 0.4–0.6 |
| >75 to ≤85 | 22 × 14 | 9 | 5.4 | +0.2/0; +0.2/0 | 0.4–0.6 |
| >85 to ≤95 | 25 × 14 | 9 | 5.4 | +0.2/0; +0.2/0 | 0.4–0.6 |
| >95 to ≤110 | 28 × 16 | 10 | 6.4 | +0.2/0; +0.2/0 | 0.4–0.6 |
| >110 to ≤130 | 32 × 18 | 11 | 7.4 | +0.3/0; +0.3/0 | 0.7–1 |
| >130 to ≤150 | 36 × 20 | 12 | 8.4 | +0.3/0; +0.3/0 | 0.7–1 |
| >150 to ≤170 | 40 × 22 | 13 | 9.4 | +0.3/0; +0.3/0 | 0.7–1 |
| >170 to ≤200 | 45 × 25 | 15 | 10.4 | +0.3/0; +0.3/0 | 0.7–1 |
| >200 to ≤230 | 50 × 28 | 17 | 11.4 | +0.3/0; +0.3/0 | 0.7–1 |
| >230 to ≤260 | 56 × 32 | 20 | 12.4 | +0.3/0; +0.3/0 | 1.2–1.6 |
| >260 to ≤290 | 63 × 32 | 20 | 12.4 | +0.3/0; +0.3/0 | 1.2–1.6 |
| >290 to ≤330 | 70 × 36 | 22 | 14.4 | +0.3/0; +0.3/0 | 1.2–1.6 |
| >330 to ≤380 | 80 × 40 | 25 | 15.4 | +0.3/0; +0.3/0 | 2–2.5 |
| >380 to ≤440 | 90 × 45 | 28 | 17.4 | +0.3/0; +0.3/0 | 2–2.5 |
| >440 to ≤500 | 100 × 50 | 31 | 19.5 | +0.3/0; +0.3/0 | 2–2.5 |
Groove-width deviations
All entries are upper / lower deviations in mm from nominal key width b. This is the groove width, not the key’s own width tolerance.
| b · mm | H9 | D10 | N9 | JS9 | P9 |
|---|---|---|---|---|---|
| 2 | +0.025 / 0 | +0.06 / +0.02 | -0.004 / -0.029 | +0.0125 / -0.0125 | -0.006 / -0.031 |
| 3 | +0.025 / 0 | +0.06 / +0.02 | -0.004 / -0.029 | +0.0125 / -0.0125 | -0.006 / -0.031 |
| 4 | +0.03 / 0 | +0.078 / +0.03 | 0 / -0.03 | +0.015 / -0.015 | -0.012 / -0.042 |
| 5 | +0.03 / 0 | +0.078 / +0.03 | 0 / -0.03 | +0.015 / -0.015 | -0.012 / -0.042 |
| 6 | +0.03 / 0 | +0.078 / +0.03 | 0 / -0.03 | +0.015 / -0.015 | -0.012 / -0.042 |
| 8 | +0.036 / 0 | +0.098 / +0.04 | 0 / -0.036 | +0.018 / -0.018 | -0.015 / -0.051 |
| 10 | +0.036 / 0 | +0.098 / +0.04 | 0 / -0.036 | +0.018 / -0.018 | -0.015 / -0.051 |
| 12 | +0.043 / 0 | +0.12 / +0.05 | 0 / -0.043 | +0.0215 / -0.0215 | -0.018 / -0.061 |
| 14 | +0.043 / 0 | +0.12 / +0.05 | 0 / -0.043 | +0.0215 / -0.0215 | -0.018 / -0.061 |
| 16 | +0.043 / 0 | +0.12 / +0.05 | 0 / -0.043 | +0.0215 / -0.0215 | -0.018 / -0.061 |
| 18 | +0.043 / 0 | +0.12 / +0.05 | 0 / -0.043 | +0.0215 / -0.0215 | -0.018 / -0.061 |
| 20 | +0.052 / 0 | +0.149 / +0.065 | 0 / -0.052 | +0.026 / -0.026 | -0.022 / -0.074 |
| 22 | +0.052 / 0 | +0.149 / +0.065 | 0 / -0.052 | +0.026 / -0.026 | -0.022 / -0.074 |
| 25 | +0.052 / 0 | +0.149 / +0.065 | 0 / -0.052 | +0.026 / -0.026 | -0.022 / -0.074 |
| 28 | +0.052 / 0 | +0.149 / +0.065 | 0 / -0.052 | +0.026 / -0.026 | -0.022 / -0.074 |
| 32 | +0.062 / 0 | +0.18 / +0.08 | 0 / -0.062 | +0.031 / -0.031 | -0.026 / -0.088 |
| 36 | +0.062 / 0 | +0.18 / +0.08 | 0 / -0.062 | +0.031 / -0.031 | -0.026 / -0.088 |
| 40 | +0.062 / 0 | +0.18 / +0.08 | 0 / -0.062 | +0.031 / -0.031 | -0.026 / -0.088 |
| 45 | +0.062 / 0 | +0.18 / +0.08 | 0 / -0.062 | +0.031 / -0.031 | -0.026 / -0.088 |
| 50 | +0.062 / 0 | +0.18 / +0.08 | 0 / -0.062 | +0.031 / -0.031 | -0.026 / -0.088 |
| 56 | +0.074 / 0 | +0.22 / +0.1 | 0 / -0.074 | +0.037 / -0.037 | -0.032 / -0.106 |
| 63 | +0.074 / 0 | +0.22 / +0.1 | 0 / -0.074 | +0.037 / -0.037 | -0.032 / -0.106 |
| 70 | +0.074 / 0 | +0.22 / +0.1 | 0 / -0.074 | +0.037 / -0.037 | -0.032 / -0.106 |
| 80 | +0.087 / 0 | +0.26 / +0.12 | 0 / -0.087 | +0.0435 / -0.0435 | -0.037 / -0.124 |
| 90 | +0.087 / 0 | +0.26 / +0.12 | 0 / -0.087 | +0.0435 / -0.0435 | -0.037 / -0.124 |
| 100 | +0.087 / 0 | +0.26 / +0.12 | 0 / -0.087 | +0.0435 / -0.0435 | -0.037 / -0.124 |
03 / How to use
How to use this calculator
- This calculator uses the GB/T 1095-2003 keyway table from the site's Chinese tool. DIN 6885-1 and ISO/R 773 values have not been verified against it, so confirm the standard named on the drawing first.
- Enter 30 mm as the nominal shaft diameter.
- Choose the connection (loose, normal or tight); it sets the shaft and hub groove-width tolerance codes.
- Read the key cross-section, shaft keyway, hub keyway and tolerance values from the result.
- Check the drawing for individual fits, key length or material notes that override the general lookup.
Table lookup, with explicit boundaries
Shaft dimension = d − t1, with deviation 0 / −t1 allowance.
Hub dimension = d + t2, with deviation +t2 allowance / 0.
Groove-width deviations apply to nominal b, not shaft diameter d.
The source accepts 6 mm in its first interval (6–8 mm). Following intervals exclude the lower endpoint and include the upper endpoint. In particular, 30 mm uses the >22–30 mm row. Inputs outside 6–500 mm are rejected.
04 / Engineering context
Keyway for a 30 mm Shaft: Parallel Key and Keyway Dimensions
A 30 mm shaft is a familiar size on motor, gearbox and general machinery drives. It carries more torque than a small instrument shaft, but the keyway still has to be selected from a standard table rather than guessed from the diameter. This page covers the parallel-key lookup for a 30 mm nominal shaft and points you to the calculator for the actual key and keyway values.
At this size, the keyway and the hub fit deserve attention together. The key transmits torque through its side faces, so the width fit, contact length and edge condition influence how the joint behaves under load. The top clearance should allow the hub to seat without the key being pinched. Reversing or shock-loaded drives can also make a loose key in its keyway work and fret, which is a design and maintenance issue rather than something a single dimension can prevent.
DIN 6885, ISO/R 773 and GB/T 1095 all use shaft diameter to enter a table of key and keyway dimensions. They are related but not a single interchangeable document, and their editions and tolerance clauses should not be mixed. The exact key width, height, keyway depths and tolerances for a 30 mm shaft are given by the on-page calculator, so read them there instead of relying on a remembered value.
GB / DIN / ISO comparison status
| Standard | Data used / status |
|---|---|
| GB/T 1095-2003 | Committed /keyway/ dimensions and width-tolerance values. |
| DIN 6885-1 | NEEDS VERIFICATION: no independent DIN table in the site dataset. |
| ISO R773 | NEEDS VERIFICATION: dimensional relationship and edition must be checked. |
No numerical DIN-versus-GB differences are inferred. Source: Chinese GB/T 1095 tool.
06 / Questions
Frequently asked questions
What keyway size does a 30 mm shaft need?
It depends on the standard and key type named for the job. A 30 mm nominal shaft selects a specific table row, and that row supplies the key and keyway dimensions. Enter 30 mm in the calculator after confirming the drawing's standard, and use the result shown for this diameter.
What key width and height fit a 30 mm shaft?
The calculator result gives the nominal key width and height for a 30 mm shaft. Do not assume a size based on a nearby shaft or on a key left in the stores. Standard diameter bands do not move in direct proportion, and the drawing may also call for a particular key type.
Are DIN 6885, ISO/R 773 and GB/T 1095 values the same for a 30 mm shaft?
The Chinese national standards catalogue (SAMR) lists GB/T 1095-2003 as a non-equivalent (NEQ) adoption of ASME B18.25.1M:1996; any relationship to ISO/R 773 is to be verified, and separate editions can still differ in detail. Use the standard cited on the drawing. Where the drawing gives no standard, resolve that question before machining rather than assuming that all three results will match.
How deep is the keyway on a 30 mm shaft?
The shaft and hub keyway depths are part of the standard lookup and are displayed by the calculator for a 30 mm shaft. They are not repeated in this article, because the value depends on the standard and key type. Check the effect of the removed section if the shaft sees high bending, shock or reversing loads.
How long should the keyway be on a 30 mm shaft?
Key length is set by hub length, transmitted torque, bearing pressure and key material, not by the 30 mm diameter alone. The calculator's cross-section result does not replace that decision. Use the drawing length or confirm it with a design check, and remember that a longer key does not automatically compensate for a poor fit.
What about the hub keyway for a 30 mm shaft?
The hub keyway is returned with the shaft keyway from the GB/T 1095 table used here. Both sides must match the key and the drawing, and the hub should seat without being distorted by an oversize key. Read the shaft and hub values from the 30 mm result before machining either component.
How do I check a worn keyway on a 30 mm shaft?
Clean the shaft and hub, inspect the side faces and edges for fretting, burrs or cracks, and measure the keyway against the drawing or standard. A worn or damaged keyway may need repair or a different design solution rather than a larger key. If the shaft is to be reused, have the condition assessed before matching it to a new key.